3D Viewport

Rendering

Depth Buffer Glitches

Sometimes when setting a large clipping range will allow you to see both near and far objects, but reduces the depth precision resulting in artifacts.

../_images/troubleshooting_3d-view_graphics-z-fighting-none.png

Model with no clipping artifacts.

../_images/troubleshooting_3d-view_graphics-z-fighting-example.png

Model with clipping artifacts.

../_images/troubleshooting_3d-view_graphics-z-fighting-example-editmode.png

Mesh with artifacts in Edit Mode.

To avoid this:

  • Increase the near clipping when working on large scenes.

  • Decrease the far clipping when objects are not viewed at a distance.

When perspective is disabled only the far Clip End is used, very high values can still result in artifacts. This is not specific to Blender, all graphics applications have these same limitations.

Objects Invisible in Camera View

If you have a large scene, viewing it through Camera View may not display all of the objects in the scene. One possibility may be that the clipping distance of the camera is too low. The camera will only show objects that fall within the clipping range.

Performance

Slow Rendering

There are a couple of reasons why you may be experiencing a slow viewport.

Old Hardware

Sometimes your hardware, mainly your graphics card, may be too slow to keep up with your model.

Upgrade Graphics Driver

In some cases, slow selection is resolved by using updated drivers.

Slow Selection

Blender uses OpenGL for selection, some graphics card drivers are slow at performing this operation.

This becomes especially problematic on dense geometry.

Possible Solutions:

GPU Depth Picking (Preferences)

See Preferences ‣ Viewport ‣ Selection.

This option is enabled by default, disabling it may give a better performance at the cost of selection accuracy.

Upgrade Graphics Driver

In some cases, slow selection is resolved by using updated drivers. It is generally good to use recent drivers when using 3D software.

Select Centers (Workaround)

In Object Mode, holding Ctrl while selecting uses the object center point. While this can be useful on its own, it has the side effect of not relying on OpenGL selection.

Change Display Mode (Workaround)

Using Wireframe display mode can be used to more quickly select different objects.

Note

Obviously, the workarounds listed here are not long term solutions, but it is handy to know if you are stuck using a system with poor OpenGL support.

Ultimately, if none of these options work out it may be worth upgrading your hardware.

Viewport Playback Frame Rate Limited

Having the viewport playback clamped to a maximum of 60 FPS is typically caused by the VSYNC setting on your GPU, for higher frame rates you may have to disable VSYNC functionality although this may be of limited us since frames rendered may be more than your GPU and monitor are able to display.

VSYNC is configured as part of your GPU driver options which vary depending on your system & GPU combination.

Navigation

Lost in Space

When navigating your scene, you may accidentally navigate away from your scene and find yourself with a blank viewport. There are two ways to fix this:

  1. Select an object in the Outliner, then zoom to that object with View ‣ Frame Selected or NumpadPeriod.

  2. Use Home to fit all objects into the 3D Viewport.

Invisible Limit Zooming In

Sometimes when navigating you may be trying to zoom in but it seems that you have hit a limit to how far you can zoom. This is because Blender uses a central point to orbit around.

In practice this is good for modeling an object which you rotate about a lot to see from all sides (think of a potter using a wheel). However, this makes it awkward to explore a scene or model an object from the ‘inside’, for example.

Solutions

Tools

Invalid Selection

There are times when selection fails under some configurations, often this is noticeable in mesh Edit Mode, selecting vertices/edges/faces where random elements are selected.

Internally Blender uses OpenGL for selection, so the graphics card driver relies on giving correct results.

Possible Solutions:

Disable Multisampling

This is by far the most common cause of selection issues.

There are known problems with some graphics cards when using multisampling.

You can disable this option by turning multisampling off in your graphics card driver options.

Change Anti-Aliasing Sample Settings

Depending on your OpenGL configuration, some specific sample settings may work while others fail.

Unfortunately finding working configuration involves trial & error testing.

Upgrade Graphics Driver

As with any OpenGL-related issues, using recent drivers can resolve problems.

However, it should be noted that this is a fairly common problem and remains unresolved with many drivers.