Inspect Results of Chaos Experiments

This document describes how to use Chaos Mesh to check running status and results of chaos experiments.

Introduction to steps of a chaos experiment

In Chaos Mesh, the life cycle of a chaos experiment is divided into four steps, according to its running process:

  • Injecting: Chaos experiment is in the process of fault injection. Normally, this step lasts for a short time. If the “Injecting” step lasts a long time, it may be due to some exceptions in the chaos experiment. In this case, you can check Events to find the cause of the exceptions.
  • Running: After the faults have been successfully injected into all target pods, the chaos experiment starts running.
  • Paused: when executing a paused process for a running chaos experiment, Chaos Mesh restores the injected faults from all target pods, which indicates the experiment is paused.
  • Finished: if the duration parameter of the experiment is configured, and when the experiment runs it up, Chaos Mesh restores the injected faults from all target pods, which indicates that the experiment is finished.

Check results using Chaos Dashboard

You can check the running steps of chaos experiments on any of the following pages using Chaos Dashboard:

  • List of chaos experiments:

    Experimental Status

  • Details of chaos experiments:

    Experimental Status

Inspect Results of Chaos Experiments - 图3note

  • If the “Injecting” step lasts for a long time, it may be due to some anomalies in the chaos experiment (e.g. the configured selectors have not selected target pods where to inject chaos actions). In this case, you can check Events to find the cause of the exceptions and check the configuration of the chaos experiment.
  • Chaos Dashboard only displays main steps of a chaos experiment. For more detailed information about experiment status and results, run the kubectl command. :::

Check results using the kubectl command

To confirm the results of chaos experiments, use the following kubectl describe command to check the Status and Events of experiment objects.

  1. kubectl describe podchaos pod-failure-tikv -n tidb-cluster

The expected output is as follows:

  1. ...
  2. Status:
  3.   Conditions:
  4.     Reason:
  5.     Status:  False
  6.     Type:    Paused
  7.     Reason:
  8.     Status:  True
  9.     Type:    Selected
  10.     Reason:
  11.     Status:  True
  12.     Type:    AllInjected
  13.     Reason:
  14.     Status:  False
  15.     Type:    AllRecovered
  16.   Experiment:
  17.     Container Records:
  18.       Id:            tidb-cluster/basic-tikv-0
  19.       Phase:         Injected
  20.       Selector Key:  .
  21.     Desired Phase:   Run
  22. Events:
  23.   Type    Reason           Age   From          Message
  24.   ----    ------           ----  ----          -------
  25.   Normal  FinalizerInited  39s   finalizer     Finalizer has been inited
  26.   Normal  Paused           39s   desiredphase  Experiment has been paused
  27.   Normal  Updated          39s   finalizer     Successfully update finalizer of resource
  28.   Normal  Updated          39s   records       Successfully update records of resource
  29.   Normal  Updated          39s   desiredphase  Successfully update desiredPhase of resource
  30.   Normal  Started          17s   desiredphase  Experiment has started
  31.   Normal  Updated          17s   desiredphase  Successfully update desiredPhase of resource
  32.   Normal  Applied          17s   records       Successfully apply chaos for tidb-cluster/basic-tikv-0
  33.   Normal  Updated          17s   records       Successfully update records of resource

The above output contains two parts:

  • Status

    Based on the running process of the chaos experiment, the Status provides four types of status records:

    • Paused: indicates the chaos experiment is in the “Paused” step.
    • Selected: indicates the chaos experiment had correctly selected the target pods where to inject chaos actions.
    • AllInjected: indicates the faults have been successfully injected to all target pods.
    • AllRecoverd: indicates the injected faults have been succesfully restored from all target pods.

    The actual running status of current chaos experiments can be inferred from these four types of status records. For example:

    • When Paused、Selected、AllRecoverd is True and AllInjected is False, it indicates the current chaos experiment is paused.
    • When Paused is True, it indicates the current chaos experiment is paused. However, if the Selected is False at the same time, then it means the current experiment cannot select the target pods where to inject chaos actions.

    Inspect Results of Chaos Experiments - 图4You can get more information from the combination of the above status records, for example, when Paused is True, it indicates the experiment is paused, but if the Selected is False at the same time, then it means the current experiment cannot select the target pods where to inject chaos actions. :::

  • Events

    It contains the records of actions conducted during the whole life cycle of a chaos experiment, which can help to check experiment status and troubleshoot issues.