Read Historical Data Using the tidb_read_staleness System Variable

To support reading the historical data, in v5.4, TiDB introduces a new system variable tidb_read_staleness. This document describes how to read historical data through this system variable, including detailed operating procedures.

Feature description

The tidb_read_staleness system variable is used to set the time range of historical data that TiDB can read in the current session. The data type of this variable is int type, and the scope of it is SESSION. After setting the value, TiDB selects a timestamp as new as possible from the range allowed by this variable, and all subsequent read operations are performed against this timestamp. For example, if the value of this variable is set to -5, on the condition that TiKV has the corresponding historical version’s data, TiDB selects a timestamp as new as possible within a 5-second time range.

After enabling tidb_read_staleness, you still can perform the following operations:

• Insert, modify, delete data or perform DML operations in the current session. These statements are not affected by tidb_read_staleness.
• Start an interactive transaction in the current session. Queries within this transaction still read the latest data.

After reading the historical data, you can read the latest data in the following two ways:

• Start a new session.
• Set the value of the tidb_read_staleness variable to "" using the SET statement.

Note

To reduce the latency and improve the timeliness of the Stale Read data, you can modify the TiKV advance-ts-interval configuration item. See Reduce Stale Read latency for details.

Usage examples

This section describes how to use tidb_read_staleness with examples.

1. Create a table, and insert a few rows of data into the table:

   create table t (c int);

   Query OK, 0 rows affected (0.01 sec)

   insert into t values (1), (2), (3);

   Query OK, 3 rows affected (0.00 sec)

2. Check out the data in the table:

   select * from t;

   +------+
   | c    |
   +------+
   |    1 |
   |    2 |
   |    3 |
   +------+
   3 rows in set (0.00 sec)

3. Update the data in a row:

   update t set c=22 where c=2;

   Query OK, 1 row affected (0.00 sec)

4. Confirm that the data has been updated:

   select * from t;

   +------+
   | c    |
   +------+
   |    1 |
   |   22 |
   |    3 |
   +------+
   3 rows in set (0.00 sec)

5. Set the tidb_read_staleness system variable.

   The scope of this variable is SESSION. After setting its value, TiDB reads the latest version data before the time set by the value.

   The following setting indicates that TiDB selects a timestamp as new as possible within the time range from 5 seconds ago to now and uses it as the timestamp for reading historical data:

   set @@tidb_read_staleness="-5";

   Query OK, 0 rows affected (0.00 sec)

   

   Note

   • Use @@ instead of @ before tidb_read_staleness. @@ means system variables, and @ means user variables.
   • You need to set the historical time range (the value of tidb_read_staleness) according to the total time that you spent in step 3 and step 4. Otherwise, the latest data will be displayed in the query results, not the historical data. Therefore, you need to adjust this time range according to the time you spent on operations. For example, in this example, since the set time range is 5 seconds, you need to complete step 3 and step 4 within 5 seconds.

   The data read here is the data before the update, that is, the historical data:

   select * from t;

   +------+
   | c    |
   +------+
   |    1 |
   |    2 |
   |    3 |
   +------+
   3 rows in set (0.00 sec)

6. After un-setting this variable as follows, TiDB can read the latest data:

   set @@tidb_read_staleness="";

   Query OK, 0 rows affected (0.00 sec)

   select * from t;

   +------+
   | c    |
   +------+
   |    1 |
   |   22 |
   |    3 |
   +------+
   3 rows in set (0.00 sec)