Prerequisites

Installer-provisioned installation of OKD requires:

1. One provisioner node with Fedora CoreOS (FCOS) installed.

2. Three control plane nodes.

3. Baseboard Management Controller (BMC) access to each node.

4. At least one network:

   1. One required routable network

   2. One optional network for provisioning nodes; and,

   3. One optional management network.

Before starting an installer-provisioned installation of OKD, ensure the hardware environment meets the following requirements.

Node requirements

Installer-provisioned installation involves a number of hardware node requirements:

• CPU architecture: All nodes must use x86_64 CPU architecture.

• Similar nodes: Red Hat recommends nodes have an identical configuration per role. That is, Red Hat recommends nodes be the same brand and model with the same CPU, memory, and storage configuration.

• Baseboard Management Controller: The provisioner node must be able to access the baseboard management controller (BMC) of each OKD cluster node. You may use IPMI, Redfish, or a proprietary protocol.

• Latest generation: Nodes must be of the most recent generation. Installer-provisioned installation relies on BMC protocols, which must be compatible across nodes. Additionally, Fedora CoreOS (FCOS) ships with the most recent drivers for RAID controllers. Ensure that the nodes are recent enough to support FCOS for the provisioner node and FCOS for the control plane and worker nodes.

• Registry node: (Optional) If setting up a disconnected mirrored registry, it is recommended the registry reside in its own node.

• Provisioner node: Installer-provisioned installation requires one provisioner node.

• Control plane: Installer-provisioned installation requires three control plane nodes for high availability.

• Worker nodes: While not required, a typical production cluster has one or more worker nodes. Smaller clusters are more resource efficient for administrators and developers during development, production, and testing.

• Network interfaces: Each node must have at least one 10GB network interface for the routable baremetal network. Each node must have one 10GB network interface for a provisioning network when using the provisioning network for deployment. Using the provisioning network is the default configuration. Network interface names must follow the same naming convention across all nodes. For example, the first NIC name on a node, such as eth0 or eno1, must be the same name on all of the other nodes. The same principle applies to the remaining NICs on each node.

• Unified Extensible Firmware Interface (UEFI): Installer-provisioned installation requires UEFI boot on all OKD nodes when using IPv6 addressing on the provisioning network. In addition, UEFI Device PXE Settings must be set to use the IPv6 protocol on the provisioning network NIC, but omitting the provisioning network removes this requirement.

• Secure Boot: Many production scenarios require nodes with Secure Boot enabled to verify the node only boots with trusted software, such as UEFI firmware drivers, EFI applications, and the operating system. To deploy an OKD cluster with Secure Boot, you must enable UEFI boot mode and Secure Boot on each control plane node and each worker node. Red Hat supports Secure Boot only when installer-provisioned installations use Red Fish Virtual Media. Red Hat does not support Secure Boot with self-generated keys.

Firmware requirements for installing with virtual media

The installer for installer-provisioned OKD clusters validates the hardware and firmware compatibility with Redfish virtual media. The following table lists supported firmware for installer-provisioned OKD clusters deployed with Redfish virtual media.

Network requirements

Installer-provisioned installation of OKD involves several network requirements. First, installer-provisioned installation involves an optional non-routable provisioning network for provisioning the operating system on each bare metal node. Second, installer-provisioned installation involves a routable baremetal network.

Configuring NICs

OKD deploys with two networks:

• provisioning: The provisioning network is an optional non-routable network used for provisioning the underlying operating system on each node that is a part of the OKD cluster. When deploying using the provisioning network, the first NIC on each node, such as eth0 or eno1, must interface with the provisioning network.

• baremetal: The baremetal network is a routable network. When deploying using the provisioning network, the second NIC on each node, such as eth1 or eno2, must interface with the baremetal network. When deploying without a provisioning network, you can use any NIC on each node to interface with the baremetal network.

Configuring the DNS server

Clients access the OKD cluster nodes over the baremetal network. A network administrator must configure a subdomain or subzone where the canonical name extension is the cluster name.

<cluster_name>.<domain-name>

For example:

test-cluster.example.com

Dynamic Host Configuration Protocol (DHCP) requirements

By default, installer-provisioned installation deploys ironic-dnsmasq with DHCP enabled for the provisioning network. No other DHCP servers should be running on the provisioning network when the provisioningNetwork configuration setting is set to managed, which is the default value. If you have a DHCP server running on the provisioning network, you must set the provisioningNetwork configuration setting to unmanaged in the install-config.yaml file.

Network administrators must reserve IP addresses for each node in the OKD cluster for the baremetal network on an external DHCP server.

Reserving IP addresses for nodes with the DHCP server

For the baremetal network, a network administrator must reserve a number of IP addresses, including:

1. Two virtual IP addresses.

   • One IP address for the API endpoint

   • One IP address for the wildcard ingress endpoint

2. One IP address for the provisioner node.

3. One IP address for each control plane (master) node.

4. One IP address for each worker node, if applicable.

The following table provides an exemplary embodiment of fully qualified domain names. The API and Nameserver addresses begin with canonical name extensions. The hostnames of the control plane and worker nodes are exemplary, so you can use any host naming convention you prefer.

Network Time Protocol (NTP)

Each OKD node in the cluster must have access to an NTP server. OKD nodes use NTP to synchronize their clocks. For example, cluster nodes use SSL certificates that require validation, which might fail if the date and time between the nodes are not in sync.

You may reconfigure the control plane nodes to act as NTP servers on disconnected clusters, and reconfigure worker nodes to retrieve time from the control plane nodes.

State-driven network configuration requirements (Technology Preview)

OKD supports additional post-installation state-driven network configuration on the secondary network interfaces of cluster nodes using kubernetes-nmstate. For example, system administrators might configure a secondary network interface on cluster nodes after installation for a storage network.

State-driven network configuration requires installing kubernetes-nmstate, and also requires Network Manager running on the cluster nodes. See OpenShift Virtualization > Kubernetes NMState (Tech Preview) for additional details.

Configuring nodes

Configuring nodes when using the provisioning network

Each node in the cluster requires the following configuration for proper installation.

While the cluster nodes can contain more than two NICs, the installation process only focuses on the first two NICs:

NIC1 is a non-routable network (provisioning) that is only used for the installation of the OKD cluster.

The Fedora CoreOS (FCOS) installation process on the provisioner node might vary. To install FCOS using a local Satellite server or a PXE server, PXE-enable NIC2.

Configure the control plane and worker nodes as follows:

Configuring nodes without the provisioning network

The installation process requires one NIC:

NICx is a routable network (baremetal) that is used for the installation of the OKD cluster, and routable to the internet.

Configuring nodes for Secure Boot

Secure Boot prevents a node from booting unless it verifies the node is using only trusted software, such as UEFI firmware drivers, EFI applications and the operating system. Red Hat only supports Secure Boot when deploying with RedFish Virtual Media.

To enable Secure Boot, refer to the hardware guide for the node. To enable Secure Boot, execute the following:

1. Boot the node and enter the BIOS menu.

2. Set the node’s boot mode to UEFI Enabled.

3. Enable Secure Boot.

   Red Hat does not support Secure Boot with self-generated keys.

Out-of-band management

Nodes will typically have an additional NIC used by the Baseboard Management Controllers (BMCs). These BMCs must be accessible from the provisioner node.

Each node must be accessible via out-of-band management. When using an out-of-band management network, the provisioner node requires access to the out-of-band management network for a successful OKD 4 installation.

The out-of-band management setup is out of scope for this document. We recommend setting up a separate management network for out-of-band management. However, using the provisioning network or the baremetal network are valid options.

Required data for installation

Prior to the installation of the OKD cluster, gather the following information from all cluster nodes:

• Out-of-band management IP

  • Examples

    • Dell (iDRAC) IP

    • HP (iLO) IP

    • Fujitsu (iRMC) IP

When using the provisioning network

• NIC1 (provisioning) MAC address

• NIC2 (baremetal) MAC address

When omitting the provisioning network

• NICx (baremetal) MAC address

Validation checklist for nodes

When using the provisioning network

• NIC1 VLAN is configured for the provisioning network. (optional)

• NIC1 is PXE-enabled on the provisioner, control plane (master), and worker nodes when using a provisioning network. (optional)

• NIC2 VLAN is configured for the baremetal network.

• PXE has been disabled on all other NICs.

• Control plane and worker nodes are configured.

• All nodes accessible via out-of-band management.

• A separate management network has been created. (optional)

• Required data for installation.

When omitting the provisioning network

• NICx VLAN is configured for the baremetal network.

• Control plane and worker nodes are configured.

• All nodes accessible via out-of-band management.

• A separate management network has been created. (optional)

• Required data for installation.