Configuring the registry for vSphere

Image registry removed during installation

On platforms that do not provide shareable object storage, the OpenShift Image Registry Operator bootstraps itself as Removed. This allows openshift-installer to complete installations on these platform types.

After installation, you must edit the Image Registry Operator configuration to switch the managementState from Removed to Managed.

Changing the image registry’s management state

To start the image registry, you must change the Image Registry Operator configuration’s managementState from Removed to Managed.

Procedure

• Change managementState Image Registry Operator configuration from Removed to Managed. For example:

  $ oc patch configs.imageregistry.operator.openshift.io cluster --type merge --patch '{"spec":{"managementState":"Managed"}}'

Image registry storage configuration

The Image Registry Operator is not initially available for platforms that do not provide default storage. After installation, you must configure your registry to use storage so that the Registry Operator is made available.

Instructions are shown for configuring a persistent volume, which is required for production clusters. Where applicable, instructions are shown for configuring an empty directory as the storage location, which is available for only non-production clusters.

Additional instructions are provided for allowing the image registry to use block storage types by using the Recreate rollout strategy during upgrades.

Configuring registry storage for VMware vSphere

As a cluster administrator, following installation you must configure your registry to use storage.

Prerequisites

• Cluster administrator permissions.

• A cluster on VMware vSphere.

• Persistent storage provisioned for your cluster, such as Red Hat OpenShift Container Storage.

  OKD supports ReadWriteOnce access for image registry storage when you have only one replica. To deploy an image registry that supports high availability with two or more replicas, ReadWriteMany access is required.

• Must have “100Gi” capacity.

Procedure

1. To configure your registry to use storage, change the spec.storage.pvc in the configs.imageregistry/cluster resource.

   When using shared storage, review your security settings to prevent outside access.

2. Verify that you do not have a registry pod:

   $ oc get pod -n openshift-image-registry

   If the storage type is emptyDIR, the replica number cannot be greater than 1.

3. Check the registry configuration:

   $ oc edit configs.imageregistry.operator.openshift.io

   Example output

   storage:
     pvc:
       claim: (1)

   1	Leave the claim field blank to allow the automatic creation of an image-registry-storage PVC.

4. Check the clusteroperator status:

   $ oc get clusteroperator image-registry

Configuring storage for the image registry in non-production clusters

You must configure storage for the Image Registry Operator. For non-production clusters, you can set the image registry to an empty directory. If you do so, all images are lost if you restart the registry.

Procedure

• To set the image registry storage to an empty directory:

  $ oc patch configs.imageregistry.operator.openshift.io cluster --type merge --patch '{"spec":{"storage":{"emptyDir":{}}}}'

  Configure this option for only non-production clusters.

  If you run this command before the Image Registry Operator initializes its components, the oc patch command fails with the following error:

  Error from server (NotFound): configs.imageregistry.operator.openshift.io "cluster" not found

  Wait a few minutes and run the command again.

Configuring block registry storage for VMware vSphere

To allow the image registry to use block storage types such as vSphere Virtual Machine Disk (VMDK) during upgrades as a cluster administrator, you can use the Recreate rollout strategy.

Procedure

1. To set the image registry storage as a block storage type, patch the registry so that it uses the Recreate rollout strategy and runs with only 1 replica:

   $ oc patch config.imageregistry.operator.openshift.io/cluster --type=merge -p '{"spec":{"rolloutStrategy":"Recreate","replicas":1}}'

2. Provision the PV for the block storage device, and create a PVC for that volume. The requested block volume uses the ReadWriteOnce (RWO) access mode.

   1. Create a pvc.yaml file with the following contents to define a VMware vSphere PersistentVolumeClaim object:

      kind: PersistentVolumeClaim
      apiVersion: v1
      metadata:
        name: image-registry-storage (1)
        namespace: openshift-image-registry (2)
      spec:
        accessModes:
        - ReadWriteOnce (3)
        resources:
          requests:
            storage: 100Gi (4)

      1	A unique name that represents the PersistentVolumeClaim object.
      2	The namespace for the PersistentVolumeClaim object, which is openshift-image-registry.
      3	The access mode of the persistent volume claim. With ReadWriteOnce, the volume can be mounted with read and write permissions by a single node.
      4	The size of the persistent volume claim.

   2. Create the PersistentVolumeClaim object from the file:

      $ oc create -f pvc.yaml -n openshift-image-registry

3. Edit the registry configuration so that it references the correct PVC:

   $ oc edit config.imageregistry.operator.openshift.io -o yaml

   Example output

   storage:
     pvc:
       claim: (1)

   1	Creating a custom PVC allows you to leave the claim field blank for the default automatic creation of an image-registry-storage PVC.

For instructions about configuring registry storage so that it references the correct PVC, see Configuring the registry for vSphere.

Additional resources

For more details about configuring registry storage for vSphere, see Recommended configurable storage technology.