Installing a cluster on vSphere with network customizations

In OKD version 4, you can install a cluster on VMware vSphere infrastructure that you provision with customized network configuration options. By customizing your network configuration, your cluster can coexist with existing IP address allocations in your environment and integrate with existing MTU and VXLAN configurations.

You must set most of the network configuration parameters during installation, and you can modify only kubeProxy configuration parameters in a running cluster.

Prerequisites

• You reviewed details about the OKD installation and update processes.

• You read the documentation on selecting a cluster installation method and preparing it for users.

• Completing the installation requires that you upload the Fedora CoreOS (FCOS) OVA on vSphere hosts. The machine from which you complete this process requires access to port 443 on the vCenter and ESXi hosts. Verify that port 443 is accessible.

• If you use a firewall, you confirmed with the administrator that port 443 is accessible. Control plane nodes must be able to reach vCenter and ESXi hosts on port 443 for the installation to succeed.

• If you use a firewall, you configured it to allow the sites that your cluster requires access to.

Preparing the user-provisioned infrastructure

Before you install OKD on user-provisioned infrastructure, you must prepare the underlying infrastructure.

This section provides details about the high-level steps required to set up your cluster infrastructure in preparation for an OKD installation. This includes configuring IP networking and network connectivity for your cluster nodes, enabling the required ports through your firewall, and setting up the required DNS and load balancing infrastructure.

After preparation, your cluster infrastructure must meet the requirements outlined in the Requirements for a cluster with user-provisioned infrastructure section.

Prerequisites

• You have reviewed the OKD 4.x Tested Integrations page.

• You have reviewed the infrastructure requirements detailed in the Requirements for a cluster with user-provisioned infrastructure section.

Procedure

1. If you are using DHCP to provide the IP networking configuration to your cluster nodes, configure your DHCP service.

   1. Add persistent IP addresses for the nodes to your DHCP server configuration. In your configuration, match the MAC address of the relevant network interface to the intended IP address for each node.

   2. When you use DHCP to configure IP addressing for the cluster machines, the machines also obtain the DNS server information through DHCP. Define the persistent DNS server address that is used by the cluster nodes through your DHCP server configuration.

      If you are not using a DHCP service, you must provide the IP networking configuration and the address of the DNS server to the nodes at FCOS install time. These can be passed as boot arguments if you are installing from an ISO image. See the Installing FCOS and starting the OKD bootstrap process section for more information about static IP provisioning and advanced networking options.

   3. Define the hostnames of your cluster nodes in your DHCP server configuration. See the Setting the cluster node hostnames through DHCP section for details about hostname considerations.

      If you are not using a DHCP service, the cluster nodes obtain their hostname through a reverse DNS lookup.

2. Ensure that your network infrastructure provides the required network connectivity between the cluster components. See the Networking requirements for user-provisioned infrastructure section for details about the requirements.

3. Configure your firewall to enable the ports required for the OKD cluster components to communicate. See Networking requirements for user-provisioned infrastructure section for details about the ports that are required.

   By default, port 1936 is accessible for an OKD cluster, because each control plane node needs access to this port. Avoid using the Ingress load balancer to expose this port, because doing so might result in the exposure of sensitive information, such as statistics and metrics, related to Ingress Controllers.

4. Setup the required DNS infrastructure for your cluster.

   1. Configure DNS name resolution for the Kubernetes API, the application wildcard, the bootstrap machine, the control plane machines, and the compute machines.

   2. Configure reverse DNS resolution for the Kubernetes API, the bootstrap machine, the control plane machines, and the compute machines.

      See the User-provisioned DNS requirements section for more information about the OKD DNS requirements.

5. Validate your DNS configuration.

   1. From your installation node, run DNS lookups against the record names of the Kubernetes API, the wildcard routes, and the cluster nodes. Validate that the IP addresses in the responses correspond to the correct components.

   2. From your installation node, run reverse DNS lookups against the IP addresses of the load balancer and the cluster nodes. Validate that the record names in the responses correspond to the correct components.

      See the Validating DNS resolution for user-provisioned infrastructure section for detailed DNS validation steps.

6. Provision the required API and application ingress load balancing infrastructure. See the Load balancing requirements for user-provisioned infrastructure section for more information about the requirements.

Validating DNS resolution for user-provisioned infrastructure

You can validate your DNS configuration before installing OKD on user-provisioned infrastructure.

Prerequisites

• You have configured the required DNS records for your user-provisioned infrastructure.

Procedure

1. From your installation node, run DNS lookups against the record names of the Kubernetes API, the wildcard routes, and the cluster nodes. Validate that the IP addresses contained in the responses correspond to the correct components.

   1. Perform a lookup against the Kubernetes API record name. Check that the result points to the IP address of the API load balancer:

      $ dig +noall +answer @<nameserver_ip> api.<cluster_name>.<base_domain> (1)

      1	Replace <nameserver_ip> with the IP address of the nameserver, <cluster_name> with your cluster name, and <base_domain> with your base domain name.

      Example output

      api.ocp4.example.com.        604800    IN    A    192.168.1.5

   2. Perform a lookup against the Kubernetes internal API record name. Check that the result points to the IP address of the API load balancer:

      $ dig +noall +answer @<nameserver_ip> api-int.<cluster_name>.<base_domain>

      Example output

      api-int.ocp4.example.com.        604800    IN    A    192.168.1.5

   3. Test an example *.apps.<cluster_name>.<base_domain> DNS wildcard lookup. All of the application wildcard lookups must resolve to the IP address of the application ingress load balancer:

      $ dig +noall +answer @<nameserver_ip> random.apps.<cluster_name>.<base_domain>

      Example output

      random.apps.ocp4.example.com.        604800    IN    A    192.168.1.5

      In the example outputs, the same load balancer is used for the Kubernetes API and application ingress traffic. In production scenarios, you can deploy the API and application ingress load balancers separately so that you can scale the load balancer infrastructure for each in isolation.

      You can replace random with another wildcard value. For example, you can query the route to the OKD console:

      $ dig +noall +answer @<nameserver_ip> console-openshift-console.apps.<cluster_name>.<base_domain>

      Example output

      console-openshift-console.apps.ocp4.example.com. 604800 IN    A 192.168.1.5

   4. Run a lookup against the bootstrap DNS record name. Check that the result points to the IP address of the bootstrap node:

      $ dig +noall +answer @<nameserver_ip> bootstrap.<cluster_name>.<base_domain>

      Example output

      bootstrap.ocp4.example.com.        604800    IN    A    192.168.1.96

   5. Use this method to perform lookups against the DNS record names for the control plane and compute nodes. Check that the results correspond to the IP addresses of each node.

2. From your installation node, run reverse DNS lookups against the IP addresses of the load balancer and the cluster nodes. Validate that the record names contained in the responses correspond to the correct components.

   1. Perform a reverse lookup against the IP address of the API load balancer. Check that the response includes the record names for the Kubernetes API and the Kubernetes internal API:

      $ dig +noall +answer @<nameserver_ip> -x 192.168.1.5

      Example output

      5.1.168.192.in-addr.arpa. 604800    IN    PTR    api-int.ocp4.example.com. (1)
      5.1.168.192.in-addr.arpa. 604800    IN    PTR    api.ocp4.example.com. (2)

      1	Provides the record name for the Kubernetes internal API.
      2	Provides the record name for the Kubernetes API.

      A PTR record is not required for the OKD application wildcard. No validation step is needed for reverse DNS resolution against the IP address of the application ingress load balancer.

   2. Perform a reverse lookup against the IP address of the bootstrap node. Check that the result points to the DNS record name of the bootstrap node:

      $ dig +noall +answer @<nameserver_ip> -x 192.168.1.96

      Example output

      96.1.168.192.in-addr.arpa. 604800    IN    PTR    bootstrap.ocp4.example.com.

   3. Use this method to perform reverse lookups against the IP addresses for the control plane and compute nodes. Check that the results correspond to the DNS record names of each node.

Generating a key pair for cluster node SSH access

During an OKD installation, you can provide an SSH public key to the installation program. The key is passed to the Fedora CoreOS (FCOS) nodes through their Ignition config files and is used to authenticate SSH access to the nodes. The key is added to the ~/.ssh/authorized_keys list for the core user on each node, which enables password-less authentication.

After the key is passed to the nodes, you can use the key pair to SSH in to the FCOS nodes as the user core. To access the nodes through SSH, the private key identity must be managed by SSH for your local user.

If you want to SSH in to your cluster nodes to perform installation debugging or disaster recovery, you must provide the SSH public key during the installation process. The ./openshift-install gather command also requires the SSH public key to be in place on the cluster nodes.

Procedure

1. If you do not have an existing SSH key pair on your local machine to use for authentication onto your cluster nodes, create one. For example, on a computer that uses a Linux operating system, run the following command:

   $ ssh-keygen -t ed25519 -N '' -f <path>/<file_name> (1)

   1	Specify the path and file name, such as ~/.ssh/id_ed25519, of the new SSH key. If you have an existing key pair, ensure your public key is in the your ~/.ssh directory.

   If you plan to install an OKD cluster that uses the Fedora cryptographic libraries that have been submitted to NIST for FIPS 140-2/140-3 Validation on only the x86_64, ppc64le, and s390x architectures, do not create a key that uses the ed25519 algorithm. Instead, create a key that uses the rsa or ecdsa algorithm.

2. View the public SSH key:

   $ cat <path>/<file_name>.pub

   For example, run the following to view the ~/.ssh/id_ed25519.pub public key:

   $ cat ~/.ssh/id_ed25519.pub

3. Add the SSH private key identity to the SSH agent for your local user, if it has not already been added. SSH agent management of the key is required for password-less SSH authentication onto your cluster nodes, or if you want to use the ./openshift-install gather command.

   On some distributions, default SSH private key identities such as ~/.ssh/id_rsa and ~/.ssh/id_dsa are managed automatically.

   1. If the ssh-agent process is not already running for your local user, start it as a background task:

      $ eval "$(ssh-agent -s)"

      Example output

      Agent pid 31874

      If your cluster is in FIPS mode, only use FIPS-compliant algorithms to generate the SSH key. The key must be either RSA or ECDSA.

4. Add your SSH private key to the ssh-agent:

   $ ssh-add <path>/<file_name> (1)

   1	Specify the path and file name for your SSH private key, such as ~/.ssh/id_ed25519

   Example output

   Identity added: /home/<you>/<path>/<file_name> (<computer_name>)

Next steps

• When you install OKD, provide the SSH public key to the installation program.

VMware vSphere region and zone enablement

You can deploy an OKD cluster to multiple vSphere datacenters that run in a single VMware vCenter. Each datacenter can run multiple clusters. This configuration reduces the risk of a hardware failure or network outage that can cause your cluster to fail.

The default installation configuration deploys a cluster to a single vSphere datacenter. If you want to deploy a cluster to multiple vSphere datacenters, you must create an installation configuration file that enables the region and zone feature.

The default install-config.yaml file includes vcenters and failureDomains fields, where you can specify multiple vSphere datacenters and clusters for your OKD cluster. You can leave these fields blank if you want to install an OKD cluster in a vSphere environment that consists of single datacenter.

The following list describes terms associated with defining zones and regions for your cluster:

• Failure domain: Establishes the relationships between a region and zone. You define a failure domain by using vCenter objects, such as a datastore object. A failure domain defines the vCenter location for OKD cluster nodes.

• Region: Specifies a vCenter datacenter. You define a region by using a tag from the openshift-region tag category.

• Zone: Specifies a vCenter cluster. You define a zone by using a tag from the openshift-zone tag category.

You must create a vCenter tag for each vCenter datacenter, which represents a region. Additionally, you must create a vCenter tag for each cluster than runs in a datacenter, which represents a zone. After you create the tags, you must attach each tag to their respective datacenters and clusters.

The following table outlines an example of the relationship among regions, zones, and tags for a configuration with multiple vSphere datacenters running in a single VMware vCenter.

Additional resources

• Additional VMware vSphere configuration parameters

• Deprecated VMware vSphere configuration parameters

• vSphere automatic migration

• VMware vSphere CSI Driver Operator

Obtaining the installation program

Before you install OKD, download the installation file on the host you are using for installation.

Prerequisites

• You have a computer that runs Linux or macOS, with 500 MB of local disk space.

Procedure

1. Download installer from https://github.com/openshift/okd/releases

   The installation program creates several files on the computer that you use to install your cluster. You must keep the installation program and the files that the installation program creates after you finish installing the cluster. Both files are required to delete the cluster.

   Deleting the files created by the installation program does not remove your cluster, even if the cluster failed during installation. To remove your cluster, complete the OKD uninstallation procedures for your specific cloud provider.

2. Extract the installation program. For example, on a computer that uses a Linux operating system, run the following command:

   $ tar -xvf openshift-install-linux.tar.gz

3. Download your installation pull secret from the Red Hat OpenShift Cluster Manager. This pull secret allows you to authenticate with the services that are provided by the included authorities, including Quay.io, which serves the container images for OKD components.

   Using a pull secret from the Red Hat OpenShift Cluster Manager is not required. You can use a pull secret for another private registry. Or, if you do not need the cluster to pull images from a private registry, you can use {"auths":{"fake":{"auth":"aWQ6cGFzcwo="}}} as the pull secret when prompted during the installation.

   If you do not use the pull secret from the Red Hat OpenShift Cluster Manager:

   • Red Hat Operators are not available.

   • The Telemetry and Insights operators do not send data to Red Hat.

   • Content from the Red Hat Ecosystem Catalog Container images registry, such as image streams and Operators, are not available.

Manually creating the installation configuration file

For user-provisioned installations of OKD, you manually generate your installation configuration file.

Prerequisites

• You have an SSH public key on your local machine to provide to the installation program. The key will be used for SSH authentication onto your cluster nodes for debugging and disaster recovery.

• You have obtained the OKD installation program and the pull secret for your cluster.

Procedure

1. Create an installation directory to store your required installation assets in:

   $ mkdir <installation_directory>

   You must create a directory. Some installation assets, like bootstrap X.509 certificates have short expiration intervals, so you must not reuse an installation directory. If you want to reuse individual files from another cluster installation, you can copy them into your directory. However, the file names for the installation assets might change between releases. Use caution when copying installation files from an earlier OKD version.

2. Customize the sample install-config.yaml file template that is provided and save it in the <installation_directory>.

   You must name this configuration file install-config.yaml.

   For some platform types, you can alternatively run ./openshift-install create install-config —dir <installation_directory> to generate an install-config.yaml file. You can provide details about your cluster configuration at the prompts.

3. Back up the install-config.yaml file so that you can use it to install multiple clusters.

   The install-config.yaml file is consumed during the next step of the installation process. You must back it up now.

Additional resources

• Installation configuration parameters

Sample install-config.yaml file for VMware vSphere

You can customize the install-config.yaml file to specify more details about your OKD cluster’s platform or modify the values of the required parameters.

additionalTrustBundlePolicy: Proxyonly
apiVersion: v1
baseDomain: example.com (1)
compute: (2)
- architecture: amd64
  name: <worker_node>
  platform: {}
  replicas: 0 (3)
controlPlane: (2)
  architecture: amd64
  name: <parent_node>
  platform: {}
  replicas: 3 (4)
metadata:
  creationTimestamp: null
  name: test (5)
networking:
---
platform:
  vsphere:
    failureDomains: (6)
    - name: <failure_domain_name>
      region: <default_region_name>
      server: <fully_qualified_domain_name>
      topology:
        computeCluster: "/<datacenter>/host/<cluster>"
        datacenter: <datacenter> (7)
        datastore: "/<datacenter>/datastore/<datastore>" (8)
        networks:
        - <VM_Network_name>
        resourcePool: "/<datacenter>/host/<cluster>/Resources/<resourcePool>" (9)
        folder: "/<datacenter_name>/vm/<folder_name>/<subfolder_name>" (10)
      zone: <default_zone_name>
    vcenters:
    - datacenters:
      - <datacenter>
      password: <password> (11)
      port: 443
      server: <fully_qualified_domain_name> (12)
      user: administrator@vsphere.local
    diskType: thin (13)
pullSecret: '{"auths":{"<local_registry>": {"auth": "<credentials>","email": "you@example.com"}}}' (14)
sshKey: 'ssh-ed25519 AAAA...' (15)
additionalTrustBundle: | (16)
  -----BEGIN CERTIFICATE-----
  ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
  -----END CERTIFICATE-----
imageContentSources: (17)
- mirrors:
  - <mirror_host_name>:<mirror_port>/<repo_name>/release
  source: <source_image_1>
- mirrors:
  - <mirror_host_name>:<mirror_port>/<repo_name>/release-images
  source: <source_image_2>

Configuring the cluster-wide proxy during installation

Production environments can deny direct access to the internet and instead have an HTTP or HTTPS proxy available. You can configure a new OKD cluster to use a proxy by configuring the proxy settings in the install-config.yaml file.

Prerequisites

• You have an existing install-config.yaml file.

• You reviewed the sites that your cluster requires access to and determined whether any of them need to bypass the proxy. By default, all cluster egress traffic is proxied, including calls to hosting cloud provider APIs. You added sites to the Proxy object’s spec.noProxy field to bypass the proxy if necessary.

  The Proxy object status.noProxy field is populated with the values of the networking.machineNetwork[].cidr, networking.clusterNetwork[].cidr, and networking.serviceNetwork[] fields from your installation configuration. For installations on Amazon Web Services (AWS), Google Cloud Platform (GCP), Microsoft Azure, and OpenStack, the Proxy object status.noProxy field is also populated with the instance metadata endpoint (169.254.169.254).

Procedure

1. Edit your install-config.yaml file and add the proxy settings. For example:

   apiVersion: v1
   baseDomain: my.domain.com
   proxy:
     httpProxy: http://<username>:<pswd>@<ip>:<port> (1)
     httpsProxy: https://<username>:<pswd>@<ip>:<port> (2)
     noProxy: example.com (3)
   additionalTrustBundle: | (4)
       -----BEGIN CERTIFICATE-----
       <MY_TRUSTED_CA_CERT>
       -----END CERTIFICATE-----
   additionalTrustBundlePolicy: <policy_to_add_additionalTrustBundle> (5)

   1	A proxy URL to use for creating HTTP connections outside the cluster. The URL scheme must be http.
   2	A proxy URL to use for creating HTTPS connections outside the cluster.
   3	A comma-separated list of destination domain names, IP addresses, or other network CIDRs to exclude from proxying. Preface a domain with . to match subdomains only. For example, .y.com matches x.y.com, but not y.com. Use * to bypass the proxy for all destinations. You must include vCenter’s IP address and the IP range that you use for its machines.
   4	If provided, the installation program generates a config map that is named user-ca-bundle in the openshift-config namespace to hold the additional CA certificates. If you provide additionalTrustBundle and at least one proxy setting, the Proxy object is configured to reference the user-ca-bundle config map in the trustedCA field. The Cluster Network Operator then creates a trusted-ca-bundle config map that merges the contents specified for the trustedCA parameter with the FCOS trust bundle. The additionalTrustBundle field is required unless the proxy’s identity certificate is signed by an authority from the FCOS trust bundle.
   5	Optional: The policy to determine the configuration of the Proxy object to reference the user-ca-bundle config map in the trustedCA field. The allowed values are Proxyonly and Always. Use Proxyonly to reference the user-ca-bundle config map only when http/https proxy is configured. Use Always to always reference the user-ca-bundle config map. The default value is Proxyonly.

   The installation program does not support the proxy readinessEndpoints field.

   If the installer times out, restart and then complete the deployment by using the wait-for command of the installer. For example: $ ./openshift-install wait-for install-complete —log-level debug

2. Save the file and reference it when installing OKD.

The installation program creates a cluster-wide proxy that is named cluster that uses the proxy settings in the provided install-config.yaml file. If no proxy settings are provided, a cluster Proxy object is still created, but it will have a nil spec.

Configuring regions and zones for a VMware vCenter

You can modify the default installation configuration file, so that you can deploy an OKD cluster to multiple vSphere datacenters that run in a single VMware vCenter.

The default install-config.yaml file configuration from the previous release of OKD is deprecated. You can continue to use the deprecated default configuration, but the openshift-installer will prompt you with a warning message that indicates the use of deprecated fields in the configuration file.

Prerequisites

• You have an existing install-config.yaml installation configuration file.

  You must specify at least one failure domain for your OKD cluster, so that you can provision datacenter objects for your VMware vCenter server. Consider specifying multiple failure domains if you need to provision virtual machine nodes in different datacenters, clusters, datastores, and other components.

Procedure

1. Enter the following govc command-line tool commands to create the openshift-region and openshift-zone vCenter tag categories:

   If you specify different names for the openshift-region and openshift-zone vCenter tag categories, the installation of the OKD cluster fails.

   $ govc tags.category.create -d "OpenShift region" openshift-region

   $ govc tags.category.create -d "OpenShift zone" openshift-zone

2. To create a region tag for each region vSphere datacenter where you want to deploy your cluster, enter the following command in your terminal:

   $ govc tags.create -c <region_tag_category> <region_tag>

3. To create a zone tag for each vSphere cluster where you want to deploy your cluster, enter the following command:

   $ govc tags.create -c <zone_tag_category> <zone_tag>

4. Attach region tags to each vCenter datacenter object by entering the following command:

   $ govc tags.attach -c <region_tag_category> <region_tag_1> /<datacenter_1>

5. Attach the zone tags to each vCenter datacenter object by entering the following command:

   $ govc tags.attach -c <zone_tag_category> <zone_tag_1> /<datacenter_1>/host/vcs-mdcnc-workload-1

6. Change to the directory that contains the installation program and initialize the cluster deployment according to your chosen installation requirements.

Sample install-config.yaml file with multiple datacenters defined in a vSphere center

---
compute:
---
  vsphere:
      zones:
        - "<machine_pool_zone_1>"
        - "<machine_pool_zone_2>"
---
controlPlane:
---
vsphere:
      zones:
        - "<machine_pool_zone_1>"
        - "<machine_pool_zone_2>"
---
platform:
  vsphere:
    vcenters:
---
    datacenters:
      - <datacenter1_name>
      - <datacenter2_name>
    failureDomains:
    - name: <machine_pool_zone_1>
      region: <region_tag_1>
      zone: <zone_tag_1>
      server: <fully_qualified_domain_name>
      topology:
        datacenter: <datacenter1>
        computeCluster: "/<datacenter1>/host/<cluster1>"
        networks:
        - <VM_Network1_name>
        datastore: "/<datacenter1>/datastore/<datastore1>"
        resourcePool: "/<datacenter1>/host/<cluster1>/Resources/<resourcePool1>"
        folder: "/<datacenter1>/vm/<folder1>"
    - name: <machine_pool_zone_2>
      region: <region_tag_2>
      zone: <zone_tag_2>
      server: <fully_qualified_domain_name>
      topology:
        datacenter: <datacenter2>
        computeCluster: "/<datacenter2>/host/<cluster2>"
        networks:
        - <VM_Network2_name>
        datastore: "/<datacenter2>/datastore/<datastore2>"
        resourcePool: "/<datacenter2>/host/<cluster2>/Resources/<resourcePool2>"
        folder: "/<datacenter2>/vm/<folder2>"
---

Network configuration phases

There are two phases prior to OKD installation where you can customize the network configuration.

Phase 1

You can customize the following network-related fields in the install-config.yaml file before you create the manifest files:

• networking.networkType

• networking.clusterNetwork

• networking.serviceNetwork

• networking.machineNetwork

  For more information on these fields, refer to Installation configuration parameters.

  Set the networking.machineNetwork to match the CIDR that the preferred NIC resides in.

  The CIDR range 172.17.0.0/16 is reserved by libVirt. You cannot use this range or any range that overlaps with this range for any networks in your cluster.

Phase 2

After creating the manifest files by running openshift-install create manifests, you can define a customized Cluster Network Operator manifest with only the fields you want to modify. You can use the manifest to specify advanced network configuration.

You cannot override the values specified in phase 1 in the install-config.yaml file during phase 2. However, you can further customize the network plugin during phase 2.

Specifying advanced network configuration

You can use advanced network configuration for your network plugin to integrate your cluster into your existing network environment. You can specify advanced network configuration only before you install the cluster.

Prerequisites

• You have created the install-config.yaml file and completed any modifications to it.

Procedure

1. Change to the directory that contains the installation program and create the manifests:

   $ ./openshift-install create manifests --dir <installation_directory> (1)

   1	<installation_directory> specifies the name of the directory that contains the install-config.yaml file for your cluster.

2. Create a stub manifest file for the advanced network configuration that is named cluster-network-03-config.yml in the <installation_directory>/manifests/ directory:

   apiVersion: operator.openshift.io/v1
   kind: Network
   metadata:
     name: cluster
   spec:

3. Specify the advanced network configuration for your cluster in the cluster-network-03-config.yml file, such as in the following examples:

   Specify a different VXLAN port for the OpenShift SDN network provider

   apiVersion: operator.openshift.io/v1
   kind: Network
   metadata:
     name: cluster
   spec:
     defaultNetwork:
       openshiftSDNConfig:
         vxlanPort: 4800

   Enable IPsec for the OVN-Kubernetes network provider

   apiVersion: operator.openshift.io/v1
   kind: Network
   metadata:
     name: cluster
   spec:
     defaultNetwork:
       ovnKubernetesConfig:
         ipsecConfig: {}

4. Optional: Back up the manifests/cluster-network-03-config.yml file. The installation program consumes the manifests/ directory when you create the Ignition config files.

5. Remove the Kubernetes manifest files that define the control plane machines and compute machineSets:

   $ rm -f openshift/99_openshift-cluster-api_master-machines-*.yaml openshift/99_openshift-cluster-api_worker-machineset-*.yaml

   Because you create and manage these resources yourself, you do not have to initialize them.

   • You can preserve the MachineSet files to create compute machines by using the machine API, but you must update references to them to match your environment.

Cluster Network Operator configuration

The configuration for the cluster network is specified as part of the Cluster Network Operator (CNO) configuration and stored in a custom resource (CR) object that is named cluster. The CR specifies the fields for the Network API in the operator.openshift.io API group.

The CNO configuration inherits the following fields during cluster installation from the Network API in the Network.config.openshift.io API group and these fields cannot be changed:

clusterNetwork

IP address pools from which pod IP addresses are allocated.

serviceNetwork

IP address pool for services.

defaultNetwork.type

Cluster network plugin, such as OpenShift SDN or OVN-Kubernetes.

You can specify the cluster network plugin configuration for your cluster by setting the fields for the defaultNetwork object in the CNO object named cluster.

Cluster Network Operator configuration object

The fields for the Cluster Network Operator (CNO) are described in the following table:

spec:
  clusterNetwork:
  - cidr: 10.128.0.0/19
    hostPrefix: 23
  - cidr: 10.128.32.0/19
    hostPrefix: 23

spec:
  serviceNetwork:
  - 172.30.0.0/14

defaultNetwork object configuration

The values for the defaultNetwork object are defined in the following table:

Configuration for the OpenShift SDN network plugin

The following table describes the configuration fields for the OpenShift SDN network plugin:

Example OpenShift SDN configuration

defaultNetwork:
  type: OpenShiftSDN
  openshiftSDNConfig:
    mode: NetworkPolicy
    mtu: 1450
    vxlanPort: 4789

Configuration for the OVN-Kubernetes network plugin

The following table describes the configuration fields for the OVN-Kubernetes network plugin:

Example OVN-Kubernetes configuration with IPSec enabled

defaultNetwork:
  type: OVNKubernetes
  ovnKubernetesConfig:
    mtu: 1400
    genevePort: 6081
    ipsecConfig: {}

kubeProxyConfig object configuration

The values for the kubeProxyConfig object are defined in the following table:

kubeProxyConfig:
  proxyArguments:
    iptables-min-sync-period:
    - 0s

Creating the Ignition config files

Because you must manually start the cluster machines, you must generate the Ignition config files that the cluster needs to make its machines.

Prerequisites

• Obtain the OKD installation program and the pull secret for your cluster.

Procedure

• Obtain the Ignition config files:

  $ ./openshift-install create ignition-configs --dir <installation_directory> (1)

  1	For <installation_directory>, specify the directory name to store the files that the installation program creates.

  If you created an install-config.yaml file, specify the directory that contains it. Otherwise, specify an empty directory. Some installation assets, like bootstrap X.509 certificates have short expiration intervals, so you must not reuse an installation directory. If you want to reuse individual files from another cluster installation, you can copy them into your directory. However, the file names for the installation assets might change between releases. Use caution when copying installation files from an earlier OKD version.

  The following files are generated in the directory:

  .
  ├── auth
  │   ├── kubeadmin-password
  │   └── kubeconfig
  ├── bootstrap.ign
  ├── master.ign
  ├── metadata.json
  └── worker.ign

Extracting the infrastructure name

The Ignition config files contain a unique cluster identifier that you can use to uniquely identify your cluster in VMware vSphere. If you plan to use the cluster identifier as the name of your virtual machine folder, you must extract it.

Prerequisites

• You obtained the OKD installation program and the pull secret for your cluster.

• You generated the Ignition config files for your cluster.

• You installed the jq package.

Procedure

• To extract and view the infrastructure name from the Ignition config file metadata, run the following command:

  $ jq -r .infraID <installation_directory>/metadata.json (1)

  1	For <installation_directory>, specify the path to the directory that you stored the installation files in.

  Example output

  openshift-vw9j6 (1)

  1	The output of this command is your cluster name and a random string.

Installing FCOS and starting the OKD bootstrap process

To install OKD on user-provisioned infrastructure on VMware vSphere, you must install Fedora CoreOS (FCOS) on vSphere hosts. When you install FCOS, you must provide the Ignition config file that was generated by the OKD installation program for the type of machine you are installing. If you have configured suitable networking, DNS, and load balancing infrastructure, the OKD bootstrap process begins automatically after the FCOS machines have rebooted.

Prerequisites

• You have obtained the Ignition config files for your cluster.

• You have access to an HTTP server that you can access from your computer and that the machines that you create can access.

• You have created a vSphere cluster.

Procedure

1. Upload the bootstrap Ignition config file, which is named <installation_directory>/bootstrap.ign, that the installation program created to your HTTP server. Note the URL of this file.

2. Save the following secondary Ignition config file for your bootstrap node to your computer as <installation_directory>/merge-bootstrap.ign:

   {
     "ignition": {
       "config": {
         "merge": [
           {
             "source": "<bootstrap_ignition_config_url>", (1)
             "verification": {}
           }
         ]
       },
       "timeouts": {},
       "version": "3.2.0"
     },
     "networkd": {},
     "passwd": {},
     "storage": {},
     "systemd": {}
   }

   1	Specify the URL of the bootstrap Ignition config file that you hosted.

   When you create the virtual machine (VM) for the bootstrap machine, you use this Ignition config file.

3. Locate the following Ignition config files that the installation program created:

   • <installation_directory>/master.ign

   • <installation_directory>/worker.ign

   • <installation_directory>/merge-bootstrap.ign

4. Convert the Ignition config files to Base64 encoding. Later in this procedure, you must add these files to the extra configuration parameter guestinfo.ignition.config.data in your VM.

   For example, if you use a Linux operating system, you can use the base64 command to encode the files.

   $ base64 -w0 <installation_directory>/master.ign > <installation_directory>/master.64

   $ base64 -w0 <installation_directory>/worker.ign > <installation_directory>/worker.64

   $ base64 -w0 <installation_directory>/merge-bootstrap.ign > <installation_directory>/merge-bootstrap.64

   If you plan to add more compute machines to your cluster after you finish installation, do not delete these files.

5. Obtain the FCOS images from the FCOS Downloads page

6. In the vSphere Client, create a folder in your datacenter to store your VMs.

   1. Click the VMs and Templates view.

   2. Right-click the name of your datacenter.

   3. Click New Folder → New VM and Template Folder.

   4. In the window that is displayed, enter the folder name. If you did not specify an existing folder in the install-config.yaml file, then create a folder with the same name as the infrastructure ID. You use this folder name so vCenter dynamically provisions storage in the appropriate location for its Workspace configuration.

7. In the vSphere Client, create a template for the OVA image and then clone the template as needed.

   In the following steps, you create a template and then clone the template for all of your cluster machines. You then provide the location for the Ignition config file for that cloned machine type when you provision the VMs.

   1. From the Hosts and Clusters tab, right-click your cluster name and select Deploy OVF Template.

   2. On the Select an OVF tab, specify the name of the FCOS OVA file that you downloaded.

   3. On the Select a name and folder tab, set a Virtual machine name for your template, such as Template-FCOS. Click the name of your vSphere cluster and select the folder you created in the previous step.

   4. On the Select a compute resource tab, click the name of your vSphere cluster.

   5. On the Select storage tab, configure the storage options for your VM.

      • Select Thin Provision or Thick Provision, based on your storage preferences.

      • Select the datastore that you specified in your install-config.yaml file.

      • If you want to encrypt your virtual machines, select Encrypt this virtual machine. See the section titled “Requirements for encrypting virtual machines” for more information.

   6. On the Select network tab, specify the network that you configured for the cluster, if available.

   7. When creating the OVF template, do not specify values on the Customize template tab or configure the template any further.

      Do not start the original VM template. The VM template must remain off and must be cloned for new FCOS machines. Starting the VM template configures the VM template as a VM on the platform, which prevents it from being used as a template that compute machine sets can apply configurations to.

8. Optional: Update the configured virtual hardware version in the VM template, if necessary. Follow Upgrading a virtual machine to the latest hardware version in the VMware documentation for more information.

   It is recommended that you update the hardware version of the VM template to version 15 before creating VMs from it, if necessary. Using hardware version 13 for your cluster nodes running on vSphere is now deprecated. If your imported template defaults to hardware version 13, you must ensure that your ESXi host is on 6.7U3 or later before upgrading the VM template to hardware version 15. If your vSphere version is less than 6.7U3, you can skip this upgrade step; however, a future version of OKD is scheduled to remove support for hardware version 13 and vSphere versions less than 6.7U3.

9. After the template deploys, deploy a VM for a machine in the cluster.

   1. Right-click the template name and click Clone → Clone to Virtual Machine.

   2. On the Select a name and folder tab, specify a name for the VM. You might include the machine type in the name, such as control-plane-0 or compute-1.

      Ensure that all virtual machine names across a vSphere installation are unique.

   3. On the Select a name and folder tab, select the name of the folder that you created for the cluster.

   4. On the Select a compute resource tab, select the name of a host in your datacenter.

   5. On the Select clone options tab, select Customize this virtual machine’s hardware.

   6. On the Customize hardware tab, click Advanced Parameters.

      The following configuration suggestions are for example purposes only. As a cluster administrator, you must configure resources according to the resource demands placed on your cluster. To best manage cluster resources, consider creating a resource pool from the cluster’s root resource pool.

      • Optional: Override default DHCP networking in vSphere. To enable static IP networking:

        • Set your static IP configuration:

          Example command

          $ export IPCFG="ip=<ip>::<gateway>:<netmask>:<hostname>:<iface>:none nameserver=srv1 [nameserver=srv2 [nameserver=srv3 [...]]]"

          Example command

          $ export IPCFG="ip=192.168.100.101::192.168.100.254:255.255.255.0:::none nameserver=8.8.8.8"

        • Set the guestinfo.afterburn.initrd.network-kargs property before you boot a VM from an OVA in vSphere:

          Example command

          $ govc vm.change -vm "<vm_name>" -e "guestinfo.afterburn.initrd.network-kargs=${IPCFG}"

      • Add the following configuration parameter names and values by specifying data in the Attribute and Values fields. Ensure that you select the Add button for each parameter that you create.

        • guestinfo.ignition.config.data: Locate the base-64 encoded files that you created previously in this procedure, and paste the contents of the base64-encoded Ignition config file for this machine type.

        • guestinfo.ignition.config.data.encoding: Specify base64.

        • disk.EnableUUID: Specify TRUE.

        • stealclock.enable: If this parameter was not defined, add it and specify TRUE.

        • Create a child resource pool from the cluster’s root resource pool. Perform resource allocation in this child resource pool.

7.  In the **Virtual Hardware** panel of the **Customize hardware** tab, modify the specified values as required. Ensure that the amount of RAM, CPU, and disk storage meets the minimum requirements for the machine type.
8.  Complete the remaining configuration steps. On clicking the **Finish** button, you have completed the cloning operation.
9.  From the **Virtual Machines** tab, right-click on your VM and then select **Power** → **Power On**.
10.  Check the console output to verify that Ignition ran.
    Example command
    ```
    Ignition: ran on 2022/03/14 14:48:33 UTC (this boot)
    Ignition: user-provided config was applied
    ```

Next steps

• Create the rest of the machines for your cluster by following the preceding steps for each machine.

  You must create the bootstrap and control plane machines at this time. Because some pods are deployed on compute machines by default, also create at least two compute machines before you install the cluster.

Adding more compute machines to a cluster in vSphere

You can add more compute machines to a user-provisioned OKD cluster on VMware vSphere.

After your vSphere template deploys in your OKD cluster, you can deploy a virtual machine (VM) for a machine in that cluster.

Prerequisites

• Obtain the base64-encoded Ignition file for your compute machines.

• You have access to the vSphere template that you created for your cluster.

Procedure

1. Right-click the template’s name and click Clone → Clone to Virtual Machine.

2. On the Select a name and folder tab, specify a name for the VM. You might include the machine type in the name, such as compute-1.

   Ensure that all virtual machine names across a vSphere installation are unique.

3. On the Select a name and folder tab, select the name of the folder that you created for the cluster.

4. On the Select a compute resource tab, select the name of a host in your datacenter.

5. On the Select storage tab, select storage for your configuration and disk files.

6. On the Select clone options tab, select Customize this virtual machine’s hardware.

7. On the Customize hardware tab, click Advanced Parameters.

   • Add the following configuration parameter names and values by specifying data in the Attribute and Values fields. Ensure that you select the Add button for each parameter that you create.

     • guestinfo.ignition.config.data: Paste the contents of the base64-encoded compute Ignition config file for this machine type.

     • guestinfo.ignition.config.data.encoding: Specify base64.

     • disk.EnableUUID: Specify TRUE.

1. In the Virtual Hardware panel of the Customize hardware tab, modify the specified values as required. Ensure that the amount of RAM, CPU, and disk storage meets the minimum requirements for the machine type. If many networks exist, select Add New Device > Network Adapter, and then enter your network information in the fields provided by the New Network menu item.

2. Complete the remaining configuration steps. On clicking the Finish button, you have completed the cloning operation.

3. From the Virtual Machines tab, right-click on your VM and then select Power → Power On.

Next steps

• Continue to create more compute machines for your cluster.

Disk partitioning

In most cases, data partitions are originally created by installing FCOS, rather than by installing another operating system. In such cases, the OKD installer should be allowed to configure your disk partitions.

However, there are two cases where you might want to intervene to override the default partitioning when installing an OKD node:

• Create separate partitions: For greenfield installations on an empty disk, you might want to add separate storage to a partition. This is officially supported for making /var or a subdirectory of /var, such as /var/lib/etcd, a separate partition, but not both.

  For disk sizes larger than 100GB, and especially disk sizes larger than 1TB, create a separate /var partition. See “Creating a separate /var partition” and this Red Hat Knowledgebase article for more information.

  Kubernetes supports only two file system partitions. If you add more than one partition to the original configuration, Kubernetes cannot monitor all of them.

• Retain existing partitions: For a brownfield installation where you are reinstalling OKD on an existing node and want to retain data partitions installed from your previous operating system, there are both boot arguments and options to coreos-installer that allow you to retain existing data partitions.

Creating a separate /var partition

In general, disk partitioning for OKD should be left to the installer. However, there are cases where you might want to create separate partitions in a part of the filesystem that you expect to grow.

OKD supports the addition of a single partition to attach storage to either the /var partition or a subdirectory of /var. For example:

• /var/lib/containers: Holds container-related content that can grow as more images and containers are added to a system.

• /var/lib/etcd: Holds data that you might want to keep separate for purposes such as performance optimization of etcd storage.

• /var: Holds data that you might want to keep separate for purposes such as auditing.

  For disk sizes larger than 100GB, and especially larger than 1TB, create a separate /var partition.

Storing the contents of a /var directory separately makes it easier to grow storage for those areas as needed and reinstall OKD at a later date and keep that data intact. With this method, you will not have to pull all your containers again, nor will you have to copy massive log files when you update systems.

Because /var must be in place before a fresh installation of Fedora CoreOS (FCOS), the following procedure sets up the separate /var partition by creating a machine config manifest that is inserted during the openshift-install preparation phases of an OKD installation.

Procedure

1. Create a directory to hold the OKD installation files:

   $ mkdir $HOME/clusterconfig

2. Run openshift-install to create a set of files in the manifest and openshift subdirectories. Answer the system questions as you are prompted:

   $ openshift-install create manifests --dir $HOME/clusterconfig
   ? SSH Public Key ...
   $ ls $HOME/clusterconfig/openshift/
   99_kubeadmin-password-secret.yaml
   99_openshift-cluster-api_master-machines-0.yaml
   99_openshift-cluster-api_master-machines-1.yaml
   99_openshift-cluster-api_master-machines-2.yaml
   ...

3. Create a Butane config that configures the additional partition. For example, name the file $HOME/clusterconfig/98-var-partition.bu, change the disk device name to the name of the storage device on the worker systems, and set the storage size as appropriate. This example places the /var directory on a separate partition:

   variant: openshift
   version: 4.0
   metadata:
     labels:
       machineconfiguration.openshift.io/role: worker
     name: 98-var-partition
   storage:
     disks:
     - device: /dev/disk/by-id/<device_name> (1)
       partitions:
       - label: var
         start_mib: <partition_start_offset> (2)
         size_mib: <partition_size> (3)
     filesystems:
       - device: /dev/disk/by-partlabel/var
         path: /var
         format: xfs
         mount_options: [defaults, prjquota] (4)
         with_mount_unit: true

   1	The storage device name of the disk that you want to partition.
   2	When adding a data partition to the boot disk, a minimum value of 25000 mebibytes is recommended. The root file system is automatically resized to fill all available space up to the specified offset. If no value is specified, or if the specified value is smaller than the recommended minimum, the resulting root file system will be too small, and future reinstalls of FCOS might overwrite the beginning of the data partition.
   3	The size of the data partition in mebibytes.
   4	The prjquota mount option must be enabled for filesystems used for container storage.

   When creating a separate /var partition, you cannot use different instance types for worker nodes, if the different instance types do not have the same device name.

4. Create a manifest from the Butane config and save it to the clusterconfig/openshift directory. For example, run the following command:

   $ butane $HOME/clusterconfig/98-var-partition.bu -o $HOME/clusterconfig/openshift/98-var-partition.yaml

5. Run openshift-install again to create Ignition configs from a set of files in the manifest and openshift subdirectories:

   $ openshift-install create ignition-configs --dir $HOME/clusterconfig
   $ ls $HOME/clusterconfig/
   auth  bootstrap.ign  master.ign  metadata.json  worker.ign

Now you can use the Ignition config files as input to the vSphere installation procedures to install Fedora CoreOS (FCOS) systems.

Updating the bootloader using bootupd

To update the bootloader by using bootupd, you must either install bootupd on FCOS machines manually or provide a machine config with the enabled systemd unit. Unlike grubby or other bootloader tools, bootupd does not manage kernel space configuration such as passing kernel arguments.

After you have installed bootupd, you can manage it remotely from the OKD cluster.

Manual install method

You can manually install bootupd by using the bootctl command-line tool.

1. Inspect the system status:

   # bootupctl status

   Example output for x86_64

   Component EFI
     Installed: grub2-efi-x64-1:2.04-31.fc33.x86_64,shim-x64-15-8.x86_64
     Update: At latest version

2. FCOS images created without bootupd installed on them require an explicit adoption phase.

   If the system status is Adoptable, perform the adoption:

   # bootupctl adopt-and-update

   Example output

   Updated: grub2-efi-x64-1:2.04-31.fc33.x86_64,shim-x64-15-8.x86_64

3. If an update is available, apply the update so that the changes take effect on the next reboot:

   # bootupctl update

   Example output

   Updated: grub2-efi-x64-1:2.04-31.fc33.x86_64,shim-x64-15-8.x86_64

Machine config method

Another way to enable bootupd is by providing a machine config.

• Provide a machine config file with the enabled systemd unit, as shown in the following example:

  Example output

    variant: rhcos
    version: 1.1.0
    systemd:
      units:
        - name: custom-bootupd-auto.service
          enabled: true
          contents: |
            [Unit]
            Description=Bootupd automatic update
            [Service]
            ExecStart=/usr/bin/bootupctl update
            RemainAfterExit=yes
            [Install]
            WantedBy=multi-user.target

Waiting for the bootstrap process to complete

The OKD bootstrap process begins after the cluster nodes first boot into the persistent FCOS environment that has been installed to disk. The configuration information provided through the Ignition config files is used to initialize the bootstrap process and install OKD on the machines. You must wait for the bootstrap process to complete.

Prerequisites

• You have created the Ignition config files for your cluster.

• You have configured suitable network, DNS and load balancing infrastructure.

• You have obtained the installation program and generated the Ignition config files for your cluster.

• You installed FCOS on your cluster machines and provided the Ignition config files that the OKD installation program generated.

• Your machines have direct internet access or have an HTTP or HTTPS proxy available.

Procedure

1. Monitor the bootstrap process:

   $ ./openshift-install --dir <installation_directory> wait-for bootstrap-complete \ (1)
       --log-level=info (2)

   1	For <installation_directory>, specify the path to the directory that you stored the installation files in.
   2	To view different installation details, specify warn, debug, or error instead of info.

   Example output

   INFO Waiting up to 30m0s for the Kubernetes API at https://api.test.example.com:6443...
   INFO API v1.28.5 up
   INFO Waiting up to 30m0s for bootstrapping to complete...
   INFO It is now safe to remove the bootstrap resources

   The command succeeds when the Kubernetes API server signals that it has been bootstrapped on the control plane machines.

2. After the bootstrap process is complete, remove the bootstrap machine from the load balancer.

   You must remove the bootstrap machine from the load balancer at this point. You can also remove or reformat the bootstrap machine itself.

Logging in to the cluster by using the CLI

You can log in to your cluster as a default system user by exporting the cluster kubeconfig file. The kubeconfig file contains information about the cluster that is used by the CLI to connect a client to the correct cluster and API server. The file is specific to a cluster and is created during OKD installation.

Prerequisites

• You deployed an OKD cluster.

• You installed the oc CLI.

Procedure

1. Export the kubeadmin credentials:

   $ export KUBECONFIG=<installation_directory>/auth/kubeconfig (1)

   1	For <installation_directory>, specify the path to the directory that you stored the installation files in.

2. Verify you can run oc commands successfully using the exported configuration:

   $ oc whoami

   Example output

   system:admin

Approving the certificate signing requests for your machines

When you add machines to a cluster, two pending certificate signing requests (CSRs) are generated for each machine that you added. You must confirm that these CSRs are approved or, if necessary, approve them yourself. The client requests must be approved first, followed by the server requests.

Prerequisites

• You added machines to your cluster.

Procedure

1. Confirm that the cluster recognizes the machines:

   $ oc get nodes

   Example output

   NAME      STATUS    ROLES   AGE  VERSION
   master-0  Ready     master  63m  v1.28.5
   master-1  Ready     master  63m  v1.28.5
   master-2  Ready     master  64m  v1.28.5

   The output lists all of the machines that you created.

   The preceding output might not include the compute nodes, also known as worker nodes, until some CSRs are approved.

2. Review the pending CSRs and ensure that you see the client requests with the Pending or Approved status for each machine that you added to the cluster:

   $ oc get csr

   Example output

   NAME        AGE     REQUESTOR                                                                   CONDITION
   csr-8b2br   15m     system:serviceaccount:openshift-machine-config-operator:node-bootstrapper   Pending
   csr-8vnps   15m     system:serviceaccount:openshift-machine-config-operator:node-bootstrapper   Pending
   ...

   In this example, two machines are joining the cluster. You might see more approved CSRs in the list.

3. If the CSRs were not approved, after all of the pending CSRs for the machines you added are in Pending status, approve the CSRs for your cluster machines:

   Because the CSRs rotate automatically, approve your CSRs within an hour of adding the machines to the cluster. If you do not approve them within an hour, the certificates will rotate, and more than two certificates will be present for each node. You must approve all of these certificates. After the client CSR is approved, the Kubelet creates a secondary CSR for the serving certificate, which requires manual approval. Then, subsequent serving certificate renewal requests are automatically approved by the machine-approver if the Kubelet requests a new certificate with identical parameters.

   For clusters running on platforms that are not machine API enabled, such as bare metal and other user-provisioned infrastructure, you must implement a method of automatically approving the kubelet serving certificate requests (CSRs). If a request is not approved, then the oc exec, oc rsh, and oc logs commands cannot succeed, because a serving certificate is required when the API server connects to the kubelet. Any operation that contacts the Kubelet endpoint requires this certificate approval to be in place. The method must watch for new CSRs, confirm that the CSR was submitted by the node-bootstrapper service account in the system:node or system:admin groups, and confirm the identity of the node.

   • To approve them individually, run the following command for each valid CSR:

     $ oc adm certificate approve <csr_name> (1)

     1	<csr_name> is the name of a CSR from the list of current CSRs.

   • To approve all pending CSRs, run the following command:

     $ oc get csr -o go-template='{{range .items}}{{if not .status}}{{.metadata.name}}{{"\n"}}{{end}}{{end}}' | xargs --no-run-if-empty oc adm certificate approve

     Some Operators might not become available until some CSRs are approved.

4. Now that your client requests are approved, you must review the server requests for each machine that you added to the cluster:

   $ oc get csr

   Example output

   NAME        AGE     REQUESTOR                                                                   CONDITION
   csr-bfd72   5m26s   system:node:ip-10-0-50-126.us-east-2.compute.internal                       Pending
   csr-c57lv   5m26s   system:node:ip-10-0-95-157.us-east-2.compute.internal                       Pending
   ...

5. If the remaining CSRs are not approved, and are in the Pending status, approve the CSRs for your cluster machines:

   • To approve them individually, run the following command for each valid CSR:

     $ oc adm certificate approve <csr_name> (1)

     1	<csr_name> is the name of a CSR from the list of current CSRs.

   • To approve all pending CSRs, run the following command:

     $ oc get csr -o go-template='{{range .items}}{{if not .status}}{{.metadata.name}}{{"\n"}}{{end}}{{end}}' | xargs oc adm certificate approve

6. After all client and server CSRs have been approved, the machines have the Ready status. Verify this by running the following command:

   $ oc get nodes

   Example output

   NAME      STATUS    ROLES   AGE  VERSION
   master-0  Ready     master  73m  v1.28.5
   master-1  Ready     master  73m  v1.28.5
   master-2  Ready     master  74m  v1.28.5
   worker-0  Ready     worker  11m  v1.28.5
   worker-1  Ready     worker  11m  v1.28.5

   It can take a few minutes after approval of the server CSRs for the machines to transition to the Ready status.

Additional information

• For more information on CSRs, see Certificate Signing Requests.

Initial Operator configuration

After the control plane initializes, you must immediately configure some Operators so that they all become available.

Prerequisites

• Your control plane has initialized.

Procedure

1. Watch the cluster components come online:

   $ watch -n5 oc get clusteroperators

   Example output

   NAME                                       VERSION   AVAILABLE   PROGRESSING   DEGRADED   SINCE
   authentication                             4.0    True        False         False      19m
   baremetal                                  4.0    True        False         False      37m
   cloud-credential                           4.0    True        False         False      40m
   cluster-autoscaler                         4.0    True        False         False      37m
   config-operator                            4.0    True        False         False      38m
   console                                    4.0    True        False         False      26m
   csi-snapshot-controller                    4.0    True        False         False      37m
   dns                                        4.0    True        False         False      37m
   etcd                                       4.0    True        False         False      36m
   image-registry                             4.0    True        False         False      31m
   ingress                                    4.0    True        False         False      30m
   insights                                   4.0    True        False         False      31m
   kube-apiserver                             4.0    True        False         False      26m
   kube-controller-manager                    4.0    True        False         False      36m
   kube-scheduler                             4.0    True        False         False      36m
   kube-storage-version-migrator              4.0    True        False         False      37m
   machine-api                                4.0    True        False         False      29m
   machine-approver                           4.0    True        False         False      37m
   machine-config                             4.0    True        False         False      36m
   marketplace                                4.0    True        False         False      37m
   monitoring                                 4.0    True        False         False      29m
   network                                    4.0    True        False         False      38m
   node-tuning                                4.0    True        False         False      37m
   openshift-apiserver                        4.0    True        False         False      32m
   openshift-controller-manager               4.0    True        False         False      30m
   openshift-samples                          4.0    True        False         False      32m
   operator-lifecycle-manager                 4.0    True        False         False      37m
   operator-lifecycle-manager-catalog         4.0    True        False         False      37m
   operator-lifecycle-manager-packageserver   4.0    True        False         False      32m
   service-ca                                 4.0    True        False         False      38m
   storage                                    4.0    True        False         False      37m

2. Configure the Operators that are not available.

Image registry removed during installation

On platforms that do not provide shareable object storage, the OpenShift Image Registry Operator bootstraps itself as Removed. This allows openshift-installer to complete installations on these platform types.

After installation, you must edit the Image Registry Operator configuration to switch the managementState from Removed to Managed.

Image registry storage configuration

The Image Registry Operator is not initially available for platforms that do not provide default storage. After installation, you must configure your registry to use storage so that the Registry Operator is made available.

Instructions are shown for configuring a persistent volume, which is required for production clusters. Where applicable, instructions are shown for configuring an empty directory as the storage location, which is available for only non-production clusters.

Additional instructions are provided for allowing the image registry to use block storage types by using the Recreate rollout strategy during upgrades.

Configuring block registry storage for VMware vSphere

To allow the image registry to use block storage types such as vSphere Virtual Machine Disk (VMDK) during upgrades as a cluster administrator, you can use the Recreate rollout strategy.

Procedure

1. Enter the following command to set the image registry storage as a block storage type, patch the registry so that it uses the Recreate rollout strategy, and runs with only 1 replica:

   $ oc patch config.imageregistry.operator.openshift.io/cluster --type=merge -p '{"spec":{"rolloutStrategy":"Recreate","replicas":1}}'

2. Provision the PV for the block storage device, and create a PVC for that volume. The requested block volume uses the ReadWriteOnce (RWO) access mode.

   1. Create a pvc.yaml file with the following contents to define a VMware vSphere PersistentVolumeClaim object:

      kind: PersistentVolumeClaim
      apiVersion: v1
      metadata:
        name: image-registry-storage (1)
        namespace: openshift-image-registry (2)
      spec:
        accessModes:
        - ReadWriteOnce (3)
        resources:
          requests:
            storage: 100Gi (4)

      1	A unique name that represents the PersistentVolumeClaim object.
      2	The namespace for the PersistentVolumeClaim object, which is openshift-image-registry.
      3	The access mode of the persistent volume claim. With ReadWriteOnce, the volume can be mounted with read and write permissions by a single node.
      4	The size of the persistent volume claim.

   2. Enter the following command to create the PersistentVolumeClaim object from the file:

      $ oc create -f pvc.yaml -n openshift-image-registry

3. Enter the following command to edit the registry configuration so that it references the correct PVC:

   $ oc edit config.imageregistry.operator.openshift.io -o yaml

   Example output

   storage:
     pvc:
       claim: (1)

   1	By creating a custom PVC, you can leave the claim field blank for the default automatic creation of an image-registry-storage PVC.

For instructions about configuring registry storage so that it references the correct PVC, see Configuring the registry for vSphere.

Completing installation on user-provisioned infrastructure

After you complete the Operator configuration, you can finish installing the cluster on infrastructure that you provide.

Prerequisites

• Your control plane has initialized.

• You have completed the initial Operator configuration.

Procedure

1. Confirm that all the cluster components are online with the following command:

   $ watch -n5 oc get clusteroperators

   Example output

   NAME                                       VERSION   AVAILABLE   PROGRESSING   DEGRADED   SINCE
   authentication                             4.0    True        False         False      19m
   baremetal                                  4.0    True        False         False      37m
   cloud-credential                           4.0    True        False         False      40m
   cluster-autoscaler                         4.0    True        False         False      37m
   config-operator                            4.0    True        False         False      38m
   console                                    4.0    True        False         False      26m
   csi-snapshot-controller                    4.0    True        False         False      37m
   dns                                        4.0    True        False         False      37m
   etcd                                       4.0    True        False         False      36m
   image-registry                             4.0    True        False         False      31m
   ingress                                    4.0    True        False         False      30m
   insights                                   4.0    True        False         False      31m
   kube-apiserver                             4.0    True        False         False      26m
   kube-controller-manager                    4.0    True        False         False      36m
   kube-scheduler                             4.0    True        False         False      36m
   kube-storage-version-migrator              4.0    True        False         False      37m
   machine-api                                4.0    True        False         False      29m
   machine-approver                           4.0    True        False         False      37m
   machine-config                             4.0    True        False         False      36m
   marketplace                                4.0    True        False         False      37m
   monitoring                                 4.0    True        False         False      29m
   network                                    4.0    True        False         False      38m
   node-tuning                                4.0    True        False         False      37m
   openshift-apiserver                        4.0    True        False         False      32m
   openshift-controller-manager               4.0    True        False         False      30m
   openshift-samples                          4.0    True        False         False      32m
   operator-lifecycle-manager                 4.0    True        False         False      37m
   operator-lifecycle-manager-catalog         4.0    True        False         False      37m
   operator-lifecycle-manager-packageserver   4.0    True        False         False      32m
   service-ca                                 4.0    True        False         False      38m
   storage                                    4.0    True        False         False      37m

   Alternatively, the following command notifies you when all of the clusters are available. It also retrieves and displays credentials:

   $ ./openshift-install --dir <installation_directory> wait-for install-complete (1)

   1	For <installation_directory>, specify the path to the directory that you stored the installation files in.

   Example output

   INFO Waiting up to 30m0s for the cluster to initialize...

   The command succeeds when the Cluster Version Operator finishes deploying the OKD cluster from Kubernetes API server.

   The Ignition config files that the installation program generates contain certificates that expire after 24 hours, which are then renewed at that time. If the cluster is shut down before renewing the certificates and the cluster is later restarted after the 24 hours have elapsed, the cluster automatically recovers the expired certificates. The exception is that you must manually approve the pending node-bootstrapper certificate signing requests (CSRs) to recover kubelet certificates. See the documentation for Recovering from expired control plane certificates for more information. It is recommended that you use Ignition config files within 12 hours after they are generated because the 24-hour certificate rotates from 16 to 22 hours after the cluster is installed. By using the Ignition config files within 12 hours, you can avoid installation failure if the certificate update runs during installation.

2. Confirm that the Kubernetes API server is communicating with the pods.

   1. To view a list of all pods, use the following command:

      $ oc get pods --all-namespaces

      Example output

      NAMESPACE                         NAME                                            READY   STATUS      RESTARTS   AGE
      openshift-apiserver-operator      openshift-apiserver-operator-85cb746d55-zqhs8   1/1     Running     1          9m
      openshift-apiserver               apiserver-67b9g                                 1/1     Running     0          3m
      openshift-apiserver               apiserver-ljcmx                                 1/1     Running     0          1m
      openshift-apiserver               apiserver-z25h4                                 1/1     Running     0          2m
      openshift-authentication-operator authentication-operator-69d5d8bf84-vh2n8        1/1     Running     0          5m
      ...

   2. View the logs for a pod that is listed in the output of the previous command by using the following command:

      $ oc logs <pod_name> -n <namespace> (1)

      1	Specify the pod name and namespace, as shown in the output of the previous command.

      If the pod logs display, the Kubernetes API server can communicate with the cluster machines.

3. For an installation with Fibre Channel Protocol (FCP), additional steps are required to enable multipathing. Do not enable multipathing during installation.

   See “Enabling multipathing with kernel arguments on FCOS” in the Postinstallation machine configuration tasks documentation for more information.

4. Register your cluster on the Cluster registration page.

You can add extra compute machines after the cluster installation is completed by following Adding compute machines to vSphere.

Configuring vSphere DRS anti-affinity rules for control plane nodes

vSphere Distributed Resource Scheduler (DRS) anti-affinity rules can be configured to support higher availability of OKD Control Plane nodes. Anti-affinity rules ensure that the vSphere Virtual Machines for the OKD Control Plane nodes are not scheduled to the same vSphere Host.

Create an anti-affinity rule by running the following command:

Example command

$ govc cluster.rule.create \
  -name openshift4-control-plane-group \
  -dc MyDatacenter -cluster MyCluster \
  -enable \
  -anti-affinity master-0 master-1 master-2

After creating the rule, your control plane nodes are automatically migrated by vSphere so they are not running on the same hosts. This might take some time while vSphere reconciles the new rule. Successful command completion is shown in the following procedure.

The vSphere DRS anti-affinity rules need to be updated manually in the event of a control plane VM name change or migration to a new vSphere Cluster.

Procedure

1. Remove any existing DRS anti-affinity rule by running the following command:

   $ govc cluster.rule.remove \
     -name openshift4-control-plane-group \
     -dc MyDatacenter -cluster MyCluster

   Example Output

   [13-10-22 09:33:24] Reconfigure /MyDatacenter/host/MyCluster...OK

2. Create the rule again with updated names by running the following command:

   $ govc cluster.rule.create \
     -name openshift4-control-plane-group \
     -dc MyDatacenter -cluster MyOtherCluster \
     -enable \
     -anti-affinity master-0 master-1 master-2

Additional resources

• See About remote health monitoring for more information about the Telemetry service

Next steps

• Customize your cluster.

• If necessary, you can opt out of remote health reporting.

• Set up your registry and configure registry storage.

• Optional: View the events from the vSphere Problem Detector Operator to determine if the cluster has permission or storage configuration issues.

• Optional: if you created encrypted virtual machines, create an encrypted storage class.