Describes how to prepare your operating system environment for Greenplum Database software installation.

Perform the following tasks in order:

  1. Make sure your host systems meet the requirements described in Platform Requirements.
  2. Deactivate or configure SELinux.
  3. Deactivate or configure firewall software.
  4. Set the required operating system parameters.
  5. Synchronize system clocks.
  6. Create the gpadmin account.

Unless noted, these tasks should be performed for all hosts in your Greenplum Database array (master, standby master, and segment hosts).

The Greenplum Database host naming convention for the master host is mdw and for the standby master host is smdw.

The segment host naming convention is sdwN where sdw is a prefix and N is an integer. For example, segment host names would be sdw1, sdw2 and so on. NIC bonding is recommended for hosts with multiple interfaces, but when the interfaces are not bonded, the convention is to append a dash (-) and number to the host name. For example, sdw1-1 and sdw1-2 are the two interface names for host sdw1.

For information about running VMware Greenplum Database in the cloud see Cloud Services in the VMware Greenplum Partner Marketplace.

Important

When data loss is not acceptable for a Greenplum Database cluster, Greenplum master and segment mirroring is recommended. If mirroring is not enabled then Greenplum stores only one copy of the data, so the underlying storage media provides the only guarantee for data availability and correctness in the event of a hardware failure.

The VMware Greenplum on vSphere virtualized environment ensures the enforcement of anti-affinity rules required for Greenplum mirroring solutions and fully supports mirrorless deployments. Other virtualized or containerized deployment environments are generally not supported for production use unless both Greenplum master and segment mirroring are enabled.

Note

For information about upgrading VMware Greenplum from a previous version, see the VMware Greenplum Database Release Notes for the release that you are installing.

Note

Automating the configuration steps described in this topic and Installing the Greenplum Database Software with a system provisioning tool, such as Ansible, Chef, or Puppet, can save time and ensure a reliable and repeatable Greenplum Database installation.

Parent topic: Installing and Upgrading Greenplum

Deactivate or Configure SELinux

For all Greenplum Database host systems running RHEL or CentOS, SELinux must either be Disabled or configured to allow unconfined access to Greenplum processes, directories, and the gpadmin user.

If you choose to deactivate SELinux:

  1. As the root user, check the status of SELinux:

    1. # sestatus
    2. SELinuxstatus: disabled

  2. If SELinux is not deactivated, deactivate it by editing the /etc/selinux/config file. As root, change the value of the SELINUX parameter in the config file as follows:

    1. SELINUX=disabled

  3. If the System Security Services Daemon (SSSD) is installed on your systems, edit the SSSD configuration file and set the selinux_provider parameter to none to prevent SELinux-related SSH authentication denials that could occur even with SELinux deactivated. As root, edit /etc/sssd/sssd.conf and add this parameter:

    1. selinux_provider=none

  4. Reboot the system to apply any changes that you made and verify that SELinux is deactivated.

If you choose to enable SELinux in Enforcing mode, then Greenplum processes and users can operate successfully in the default Unconfined context. If you require increased SELinux confinement for Greenplum processes and users, you must test your configuration to ensure that there are no functionality or performance impacts to Greenplum Database. See the SELinux User’s and Administrator’s Guide for detailed information about configuring SELinux and SELinux users.

Deactivate or Configure Firewall Software

You should also deactivate firewall software such as iptables (on systems such as RHEL 6.x and CentOS 6.x ), firewalld (on systems such as RHEL 7.x and CentOS 7.x), or ufw (on Ubuntu systems, deactivated by default). If firewall software is not deactivated, you must instead configure your software to allow required communication between Greenplum hosts.

To deactivate iptables:

  1. As the root user, check the status of iptables:

    1. # /sbin/chkconfig --list iptables

    If iptables is deactivated, the command output is:

    1. iptables 0:off 1:off 2:off 3:off 4:off 5:off 6:off

  2. If necessary, run this command as root to deactivate iptables:

    1. /sbin/chkconfig iptables off

    You will need to reboot your system after applying the change.

  3. For systems with firewalld, check the status of firewalld with the command:

    1. # systemctl status firewalld

    If firewalld is deactivated, the command output is:

    1. * firewalld.service - firewalld - dynamic firewall daemon
    2.    Loaded: loaded (/usr/lib/systemd/system/firewalld.service; disabled; vendor preset: enabled)
    3.    Active: inactive (dead)

  4. If necessary, run these commands as root to deactivate firewalld:

    1. # systemctl stop firewalld.service
    2. # systemctl deactivate firewalld.service

If you decide to enable iptables with Greenplum Database for security purposes, see Enabling iptables (Optional) for important considerations and example configurations.

See the documentation for the firewall or your operating system for additional information.

Greenplum requires that certain Linux operating system (OS) parameters be set on all hosts in your Greenplum Database system (masters and segments).

In general, the following categories of system parameters need to be altered:

  • Shared Memory - A Greenplum Database instance will not work unless the shared memory segment for your kernel is properly sized. Most default OS installations have the shared memory values set too low for Greenplum Database. On Linux systems, you must also deactivate the OOM (out of memory) killer. For information about Greenplum Database shared memory requirements, see the Greenplum Database server configuration parameter shared_buffers in the Greenplum Database Reference Guide.
  • Network - On high-volume Greenplum Database systems, certain network-related tuning parameters must be set to optimize network connections made by the Greenplum interconnect.
  • User Limits - User limits control the resources available to processes started by a user’s shell. Greenplum Database requires a higher limit on the allowed number of file descriptors that a single process can have open. The default settings may cause some Greenplum Database queries to fail because they will run out of file descriptors needed to process the query.

More specifically, you need to edit the following Linux configuration settings:

The hosts File

Edit the /etc/hosts file and make sure that it includes the host names and all interface address names for every machine participating in your Greenplum Database system.

The sysctl.conf File

The sysctl.conf parameters listed in this topic are for performance, optimization, and consistency in a wide variety of environments. Change these settings according to your specific situation and setup.

Set the parameters in the /etc/sysctl.conf file and reload with sysctl -p:

  2. # kernel.shmall = _PHYS_PAGES / 2 # See Shared Memory Pages
  3. kernel.shmall = 197951838
  4. # kernel.shmmax = kernel.shmall * PAGE_SIZE 
  5. kernel.shmmax = 810810728448
  6. kernel.shmmni = 4096
  7. vm.overcommit_memory = 2 # See Segment Host Memory
  8. vm.overcommit_ratio = 95 # See Segment Host Memory
  10. net.ipv4.ip_local_port_range = 10000 65535 # See Port Settings
  11. kernel.sem = 250 2048000 200 8192
  12. kernel.sysrq = 1
  13. kernel.core_uses_pid = 1
  14. kernel.msgmnb = 65536
  15. kernel.msgmax = 65536
  16. kernel.msgmni = 2048
  17. net.ipv4.tcp_syncookies = 1
  18. net.ipv4.conf.default.accept_source_route = 0
  19. net.ipv4.tcp_max_syn_backlog = 4096
  20. net.ipv4.conf.all.arp_filter = 1
  21. net.ipv4.ipfrag_high_thresh = 41943040
  22. net.ipv4.ipfrag_low_thresh = 31457280
  23. net.ipv4.ipfrag_time = 60
  24. net.core.netdev_max_backlog = 10000
  25. net.core.rmem_max = 2097152
  26. net.core.wmem_max = 2097152
  27. vm.swappiness = 10
  28. vm.zone_reclaim_mode = 0
  29. vm.dirty_expire_centisecs = 500
  30. vm.dirty_writeback_centisecs = 100
  31. vm.dirty_background_ratio = 0 # See System Memory
  32. vm.dirty_ratio = 0
  33. vm.dirty_background_bytes = 1610612736
  34. vm.dirty_bytes = 4294967296

Shared Memory Pages

Greenplum Database uses shared memory to communicate between postgres processes that are part of the same postgres instance. kernel.shmall sets the total amount of shared memory, in pages, that can be used system wide. kernel.shmmax sets the maximum size of a single shared memory segment in bytes.

Set kernel.shmall and kernel.shmmax values based on your system’s physical memory and page size. In general, the value for both parameters should be one half of the system physical memory.

Use the operating system variables _PHYS_PAGES and PAGE_SIZE to set the parameters.

  1. kernel.shmall = ( _PHYS_PAGES / 2)
  2. kernel.shmmax = ( _PHYS_PAGES / 2) * PAGE_SIZE

To calculate the values for kernel.shmall and kernel.shmmax, run the following commands using the getconf command, which returns the value of an operating system variable.

  1. $ echo $(expr $(getconf _PHYS_PAGES) / 2) 
  2. $ echo $(expr $(getconf _PHYS_PAGES) / 2 \* $(getconf PAGE_SIZE))

As best practice, we recommend you set the following values in the /etc/sysctl.conf file using calculated values. For example, a host system has 1583 GB of memory installed and returns these values: _PHYS_PAGES = 395903676 and PAGE_SIZE = 4096. These would be the kernel.shmall and kernel.shmmax values:

  1. kernel.shmall = 197951838
  2. kernel.shmmax = 810810728448

If the Greenplum Database master has a different shared memory configuration than the segment hosts, the _PHYS_PAGES and PAGE_SIZE values might differ, and the kernel.shmall and kernel.shmmax values on the master host will differ from those on the segment hosts.

Segment Host Memory

The vm.overcommit_memory Linux kernel parameter is used by the OS to determine how much memory can be allocated to processes. For Greenplum Database, this parameter should always be set to 2.

vm.overcommit_ratio is the percent of RAM that is used for application processes and the remainder is reserved for the operating system. The default is 50 on Red Hat Enterprise Linux.

For vm.overcommit_ratio tuning and calculation recommendations with resource group-based resource management or resource queue-based resource management, refer to Options for Configuring Segment Host Memory in the Geenplum Database Administrator Guide.

Port Settings

To avoid port conflicts between Greenplum Database and other applications during Greenplum initialization, make a note of the port range specified by the operating system parameter net.ipv4.ip_local_port_range. When initializing Greenplum using the gpinitsystem cluster configuration file, do not specify Greenplum Database ports in that range. For example, if net.ipv4.ip_local_port_range = 10000 65535, set the Greenplum Database base port numbers to these values.

  1. PORT_BASE = 6000
  2. MIRROR_PORT_BASE = 7000

For information about the gpinitsystem cluster configuration file, see Initializing a Greenplum Database System.

For Azure deployments with Greenplum Database avoid using port 65330; add the following line to sysctl.conf:

  1. net.ipv4.ip_local_reserved_ports=65330

For additional requirements and recommendations for cloud deployments, see Greenplum Database Cloud Technical Recommendations.

IP Fragmentation Settings

When the Greenplum Database interconnect uses UDP (the default), the network interface card controls IP packet fragmentation and reassemblies.

If the UDP message size is larger than the size of the maximum transmission unit (MTU) of a network, the IP layer fragments the message. (Refer to Networking later in this topic for more information about MTU sizes for Greenplum Database.) The receiver must store the fragments in a buffer before it can reorganize and reassemble the message.

The following sysctl.conf operating system parameters control the reassembly process:

OS ParameterDescription
net.ipv4.ipfrag_high_threshThe maximum amount of memory used to reassemble IP fragments before the kernel starts to remove fragments to free up resources. The default value is 4194304 bytes (4MB).
net.ipv4.ipfrag_low_threshThe minimum amount of memory used to reassemble IP fragments. The default value is 3145728 bytes (3MB). (Deprecated after kernel version 4.17.)
net.ipv4.ipfrag_timeThe maximum amount of time (in seconds) to keep an IP fragment in memory. The default value is 30.

The recommended settings for these parameters for Greenplum Database follow:

  1. net.ipv4.ipfrag_high_thresh = 41943040
  2. net.ipv4.ipfrag_low_thresh = 31457280
  3. net.ipv4.ipfrag_time = 60

System Memory

For host systems with more than 64GB of memory, these settings are recommended:

  1. vm.dirty_background_ratio = 0
  2. vm.dirty_ratio = 0
  3. vm.dirty_background_bytes = 1610612736 # 1.5GB
  4. vm.dirty_bytes = 4294967296 # 4GB

For host systems with 64GB of memory or less, remove vm.dirty_background_bytes and vm.dirty_bytes and set the two ratio parameters to these values:

  1. vm.dirty_background_ratio = 3
  2. vm.dirty_ratio = 10

Increase vm.min_free_kbytes to ensure PF_MEMALLOC requests from network and storage drivers are easily satisfied. This is especially critical on systems with large amounts of system memory. The default value is often far too low on these systems. Use this awk command to set vm.min_free_kbytes to a recommended 3% of system physical memory:

  1. awk 'BEGIN {OFMT = "%.0f";} /MemTotal/ {print "vm.min_free_kbytes =", $2 * .03;}'
  2.                /proc/meminfo >> /etc/sysctl.conf

Do not set vm.min_free_kbytes to higher than 5% of system memory as doing so might cause out of memory conditions.

System Resources Limits

Set the following parameters in the /etc/security/limits.conf file:

  1. * soft nofile 524288
  2. * hard nofile 524288
  3. * soft nproc 131072
  4. * hard nproc 131072

For Red Hat Enterprise Linux (RHEL) and CentOS systems, parameter values in the /etc/security/limits.d/90-nproc.conf file (RHEL/CentOS 6) or /etc/security/limits.d/20-nproc.conf file (RHEL/CentOS 7) override the values in the limits.conf file. Ensure that any parameters in the override file are set to the required value. The Linux module pam_limits sets user limits by reading the values from the limits.conf file and then from the override file. For information about PAM and user limits, see the documentation on PAM and pam_limits.

Run the ulimit -u command on each segment host to display the maximum number of processes that are available to each user. Validate that the return value is 131072.

Core Dump

Enable core file generation to a known location by adding the following line to /etc/sysctl.conf:

  1. kernel.core_pattern=/var/core/core.%h.%t

Add the following line to /etc/security/limits.conf:

  1. * soft  core unlimited

To apply the changes to the live kernel, run the following command:

  1. # sysctl -p

XFS Mount Options

XFS is the preferred data storage file system on Linux platforms. Use the mount command with the following recommended XFS mount options for RHEL 7 and CentOS systems:

  1. rw,nodev,noatime,nobarrier,inode64

The nobarrier option is not supported on RHEL 8 or Ubuntu systems. Use only the options:

  1. rw,nodev,noatime,inode64

See the mount manual page (man mount opens the man page) for more information about using this command.

The XFS options can also be set in the /etc/fstab file. This example entry from an fstab file specifies the XFS options.

  1. /dev/data /data xfs nodev,noatime,inode64 0 0

Note

You must have root permission to edit the /etc/fstab file.

Disk I/O Settings

  • Read-ahead value

    Each disk device file should have a read-ahead (blockdev) value of 16384. To verify the read-ahead value of a disk device:

    1. # sudo /sbin/blockdev --getra <devname>

    For example:

    1. # sudo /sbin/blockdev --getra /dev/sdb

    To set blockdev (read-ahead) on a device:

    1. # sudo /sbin/blockdev --setra <bytes> <devname>

    For example:

    1. # sudo /sbin/blockdev --setra 16384 /dev/sdb

    See the manual page (man) for the blockdev command for more information about using that command (man blockdev opens the man page).

    Note

    The blockdev --setra command is not persistent. You must ensure the read-ahead value is set whenever the system restarts. How to set the value will vary based on your system.

    One method to set the blockdev value at system startup is by adding the /sbin/blockdev --setra command in the rc.local file. For example, add this line to the rc.local file to set the read-ahead value for the disk sdb.

    1. /sbin/blockdev --setra 16384 /dev/sdb

    On systems that use systemd, you must also set the execute permissions on the rc.local file to enable it to run at startup. For example, on a RHEL/CentOS 7 system, this command sets execute permissions on the file.

    1. # chmod +x /etc/rc.d/rc.local

    Restart the system to have the setting take effect.

  • Disk I/O scheduler

    The Linux disk scheduler orders the I/O requests submitted to a storage device, controlling the way the kernel commits reads and writes to disk.

    A typical Linux disk I/O scheduler supports multiple access policies. The optimal policy selection depends on the underlying storage infrastructure. The recommended scheduler policy settings for Greenplum Database systems for specific OSs and storage device types follow:

    Storage Device TypeOSRecommended Scheduler Policy
    Non-Volatile Memory Express (NVMe)RHEL 7
    RHEL 8
    Ubuntu    		none
    Solid-State Drives (SSD)RHEL 7noop
    RHEL 8
    Ubuntu    		none
    OtherRHEL 7deadline
    RHEL 8
    Ubuntu    		mq-deadline

    To specify a scheduler until the next system reboot, run the following:

    1. # echo schedulername > /sys/block/<devname>/queue/scheduler

    For example:

    1. # echo deadline > /sys/block/sbd/queue/scheduler

    Note

    Using the echo command to set the disk I/O scheduler policy is not persistent; you must ensure that you run the command whenever the system reboots. How to run the command will vary based on your system.

    To specify the I/O scheduler at boot time on systems that use grub2 such as RHEL 7.x or CentOS 7.x, use the system utility grubby. This command adds the parameter when run as root:

    1. # grubby --update-kernel=ALL --args="elevator=deadline"

    After adding the parameter, reboot the system.

    This grubby command displays kernel parameter settings:

    1. # grubby --info=ALL

    Refer to your operating system documentation for more information about the grubby utility. If you used the grubby command to configure the disk scheduler on a RHEL or CentOS 7.x system and it does not update the kernels, see the Note at the end of the section.

    For additional information about configuring the disk scheduler, refer to the RedHat Enterprise Linux documentation for RHEL 7 or RHEL 8. The Ubuntu wiki IOSchedulers topic describes the I/O schedulers available on Ubuntu systems.

Networking

The maximum transmission unit (MTU) of a network specifies the size (in bytes) of the largest data packet/frame accepted by a network-connected device. A jumbo frame is a frame that contains more than the standard MTU of 1500 bytes.

Greenplum Database utilizes 3 distinct MTU settings:

  • The Greenplum Database gp_max_packet_size server configuration parameter. The default max packet size is 8192. This default assumes a jumbo frame MTU.
  • The operating system MTU setting.
  • The rack switch MTU setting.

These settings are connected, in that they should always be either the same, or close to the same, value, or otherwise in the order of Greenplum < OS < switch for MTU size.

9000 is a common supported setting for switches, and is the recommended OS and rack switch MTU setting for your Greenplum Database hosts.

Transparent Huge Pages (THP)

Deactivate Transparent Huge Pages (THP) as it degrades Greenplum Database performance. RHEL 6.0 or higher enables THP by default. One way to deactivate THP on RHEL 6.x is by adding the parameter transparent_hugepage=never to the kernel command in the file /boot/grub/grub.conf, the GRUB boot loader configuration file. This is an example kernel command from a grub.conf file. The command is on multiple lines for readability:

  1. kernel /vmlinuz-2.6.18-274.3.1.el5 ro root=LABEL=/
  2.            elevator=deadline crashkernel=128M@16M  quiet console=tty1
  3.            console=ttyS1,115200 panic=30 transparent_hugepage=never 
  4.            initrd /initrd-2.6.18-274.3.1.el5.img

On systems that use grub2 such as RHEL 7.x or CentOS 7.x, use the system utility grubby. This command adds the parameter when run as root.

  1. # grubby --update-kernel=ALL --args="transparent_hugepage=never"

After adding the parameter, reboot the system.

For Ubuntu systems, install the hugepages package and run this command as root:

  1. # hugeadm --thp-never

This cat command checks the state of THP. The output indicates that THP is deactivated.

  1. $ cat /sys/kernel/mm/*transparent_hugepage/enabled
  2. always [never]

For more information about Transparent Huge Pages or the grubby utility, see your operating system documentation. If the grubby command does not update the kernels, see the Note at the end of the section.

IPC Object Removal

Deactivate IPC object removal for RHEL 7.2 or CentOS 7.2, or Ubuntu. The default systemd setting RemoveIPC=yes removes IPC connections when non-system user accounts log out. This causes the Greenplum Database utility gpinitsystem to fail with semaphore errors. Perform one of the following to avoid this issue.

  • When you add the gpadmin operating system user account to the master node in Creating the Greenplum Administrative User, create the user as a system account.

  • Deactivate RemoveIPC. Set this parameter in /etc/systemd/logind.conf on the Greenplum Database host systems.

    1. RemoveIPC=no

    The setting takes effect after restarting the systemd-login service or rebooting the system. To restart the service, run this command as the root user.

    1. service systemd-logind restart

SSH Connection Threshold

Certain Greenplum Database management utilities including gpexpand, gpinitsystem, and gpaddmirrors, use secure shell (SSH) connections between systems to perform their tasks. In large Greenplum Database deployments, cloud deployments, or deployments with a large number of segments per host, these utilities may exceed the host’s maximum threshold for unauthenticated connections. When this occurs, you receive errors such as: ssh_exchange_identification: Connection closed by remote host.

To increase this connection threshold for your Greenplum Database system, update the SSH MaxStartups and MaxSessions configuration parameters in one of the /etc/ssh/sshd_config or /etc/sshd_config SSH daemon configuration files.

Note

You must have root permission to edit these two files.

If you specify MaxStartups and MaxSessions using a single integer value, you identify the maximum number of concurrent unauthenticated connections (MaxStartups) and maximum number of open shell, login, or subsystem sessions permitted per network connection (MaxSessions). For example:

  1. MaxStartups 200
  2. MaxSessions 200

If you specify MaxStartups using the “start:rate:full” syntax, you enable random early connection drop by the SSH daemon. start identifies the maximum number of unauthenticated SSH connection attempts allowed. Once start number of unauthenticated connection attempts is reached, the SSH daemon refuses rate percent of subsequent connection attempts. full identifies the maximum number of unauthenticated connection attempts after which all attempts are refused. For example:

  1. Max Startups 10:30:200
  2. MaxSessions 200

Restart the SSH daemon after you update MaxStartups and MaxSessions. For example, on a CentOS 6 system, run the following command as the root user:

  1. # service sshd restart

For detailed information about SSH configuration options, refer to the SSH documentation for your Linux distribution.

Note

If the grubby command does not update the kernels of a RHEL 7.x or CentOS 7.x system, you can manually update all kernels on the system. For example, to add the parameter transparent_hugepage=never to all kernels on a system.

  1. Add the parameter to the GRUB_CMDLINE_LINUX line in the file parameter in /etc/default/grub.

    1. GRUB_TIMEOUT=5
    2. GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)"
    3. GRUB_DEFAULT=saved
    4. GRUB_DISABLE_SUBMENU=true
    5. GRUB_TERMINAL_OUTPUT="console"
    6. GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=cl/root rd.lvm.lv=cl/swap rhgb quiet transparent_hugepage=never"
    7.               GRUB_DISABLE_RECOVERY="true"

    Note

    You must have root permission to edit the /etc/default/grub file.

  2. As root, run the grub2-mkconfig command to update the kernels.

    1. # grub2-mkconfig -o /boot/grub2/grub.cfg

  3. Reboot the system.

Synchronizing System Clocks

You should use NTP (Network Time Protocol) to synchronize the system clocks on all hosts that comprise your Greenplum Database system. See www.ntp.org for more information about NTP.

NTP on the segment hosts should be configured to use the master host as the primary time source, and the standby master as the secondary time source. On the master and standby master hosts, configure NTP to point to your preferred time server.

To configure NTP

  1. On the master host, log in as root and edit the /etc/ntp.conf file. Set the server parameter to point to your data center’s NTP time server. For example (if 10.6.220.20 was the IP address of your data center’s NTP server):

    1. server 10.6.220.20

  2. On each segment host, log in as root and edit the /etc/ntp.conf file. Set the first server parameter to point to the master host, and the second server parameter to point to the standby master host. For example:

    1. server mdw prefer
    2. server smdw

  3. On the standby master host, log in as root and edit the /etc/ntp.conf file. Set the first server parameter to point to the primary master host, and the second server parameter to point to your data center’s NTP time server. For example:

    1. server mdw prefer
    2. server 10.6.220.20

  4. On the master host, use the NTP daemon synchronize the system clocks on all Greenplum hosts. For example, using gpssh:

    1. # gpssh -f hostfile_gpssh_allhosts -v -e 'ntpd'

Creating the Greenplum Administrative User

Create a dedicated operating system user account on each node to run and administer Greenplum Database. This user account is named gpadmin by convention.

Important

You cannot run the Greenplum Database server as root.

The gpadmin user must have permission to access the services and directories required to install and run Greenplum Database.

The gpadmin user on each Greenplum host must have an SSH key pair installed and be able to SSH from any host in the cluster to any other host in the cluster without entering a password or passphrase (called “passwordless SSH”). If you enable passwordless SSH from the master host to every other host in the cluster (“1-n passwordless SSH”), you can use the Greenplum Database gpssh-exkeys command-line utility later to enable passwordless SSH from every host to every other host (“n-n passwordless SSH”).

You can optionally give the gpadmin user sudo privilege, so that you can easily administer all hosts in the Greenplum Database cluster as gpadmin using the sudo, ssh/scp, and gpssh/gpscp commands.

The following steps show how to set up the gpadmin user on a host, set a password, create an SSH key pair, and (optionally) enable sudo capability. These steps must be performed as root on every Greenplum Database cluster host. (For a large Greenplum Database cluster you will want to automate these steps using your system provisioning tools.)

Note

See Example Ansible Playbook for an example that shows how to automate the tasks of creating the gpadmin user and installing the Greenplum Database software on all hosts in the cluster.

  1. Create the gpadmin group and user.

    Note

    If you are installing Greenplum Database on RHEL 7.2 or CentOS 7.2 and want to deactivate IPC object removal by creating the gpadmin user as a system account, provide both the -r option (create the user as a system account) and the -m option (create a home directory) to the useradd command. On Ubuntu systems, you must use the -m option with the useradd command to create a home directory for a user.

    This example creates the gpadmin group, creates the gpadmin user as a system account with a home directory and as a member of the gpadmin group, and creates a password for the user.

    1. # groupadd gpadmin
    2. # useradd gpadmin -r -m -g gpadmin
    3. # passwd gpadmin
    4. New password: <changeme>
    5. Retype new password: <changeme>

    Note

    You must have root permission to create the gpadmin group and user.

    Note

    Make sure the gpadmin user has the same user id (uid) and group id (gid) numbers on each host to prevent problems with scripts or services that use them for identity or permissions. For example, backing up Greenplum databases to some networked filesy stems or storage appliances could fail if the gpadmin user has different uid or gid numbers on different segment hosts. When you create the gpadmin group and user, you can use the groupadd -g option to specify a gid number and the useradd -u option to specify the uid number. Use the command id gpadmin to see the uid and gid for the gpadmin user on the current host.

  2. Switch to the gpadmin user and generate an SSH key pair for the gpadmin user.

    1. $ su gpadmin
    2. $ ssh-keygen -t rsa -b 4096
    3. Generating public/private rsa key pair.
    4. Enter file in which to save the key (/home/gpadmin/.ssh/id_rsa):
    5. Created directory '/home/gpadmin/.ssh'.
    6. Enter passphrase (empty for no passphrase):
    7. Enter same passphrase again:

    At the passphrase prompts, press Enter so that SSH connections will not require entry of a passphrase.

  3. Grant sudo access to the gpadmin user.

    On Red Hat or CentOS, run visudo and uncomment the %wheel group entry.

    1. %wheel        ALL=(ALL)       NOPASSWD: ALL

    Make sure you uncomment the line that has the NOPASSWD keyword.

    Add the gpadmin user to the wheel group with this command.

    1. # usermod -aG wheel gpadmin

Next Steps