Installation Details

The installation is broken up into two different use cases: single and multi-cluster. The single cluster install is for if you wish to use GitOps to manage a single cluster, in which case you do not need a centralized manager cluster. In the multi-cluster use case you will setup a centralized manager cluster to which you can register clusters.

If you are just learning Fleet the single cluster install is the recommended starting point. After which you can move from single cluster to multi-cluster setup down the line.

Installation Details - 图1

Single-cluster is the default installation. The same cluster will run both the Fleet manager and the Fleet agent. The cluster will communicate with Git server to deploy resources to this local cluster. This is the simplest setup and very useful for dev/test and small scale setups. This use case is supported as a valid use case for production.

Prerequisites

  • Helm 3
  • Kubernetes

Fleet is distributed as a Helm chart. Helm 3 is a CLI, has no server side component, and is fairly straight forward. To install the Helm 3 CLI follow the official install instructions.

Fleet is a controller running on a Kubernetes cluster so an existing cluster is required. For the single cluster use case you will install Fleet to the cluster which you intend to manage with GitOps. Any Kubernetes community supported version of Kubernetes will work, in practice this means or greater.

Default Install

Install the following two Helm charts.

  • Install
  • Verify

First install the Fleet CustomResourcesDefintions.

  1. helm -n cattle-fleet-system install --create-namespace --wait \
  2.     fleet-crd https://github.com/rancher/fleet/releases/download/v0.6.0/fleet-crd-0.6.0.tgz

Second install the Fleet controllers.

  1. helm -n cattle-fleet-system install --create-namespace --wait \
  2.     fleet https://github.com/rancher/fleet/releases/download/v0.6.0/fleet-0.6.0.tgz

Fleet should be ready to use now for single cluster. You can check the status of the Fleet controller pods by running the below commands.

  1. kubectl -n cattle-fleet-system logs -l app=fleet-controller
  2. kubectl -n cattle-fleet-system get pods -l app=fleet-controller
  1. NAME                                READY   STATUS    RESTARTS   AGE
  2. fleet-controller-64f49d756b-n57wq   1/1     Running   0          3m21s

You can now register some git repos in the fleet-local namespace to start deploying Kubernetes resources.

Configuration for Multi-Cluster

Installation Details - 图2caution

Downstream clusters in Rancher are automatically registered in Fleet. Users can access Fleet under Continuous Delivery on Rancher.

The multi-cluster install described below is only covered in standalone Fleet, which is untested by Rancher QA.

Installation Details - 图3info

The setup is the same as for a single cluster. After installing the Fleet manager, you will then need to register remote downstream clusters with the Fleet manager.

However, to allow for manager-initiated registration of downstream clusters, a few extra settings are required. Without the API server URL and the CA, only agent-initiated registration of downstream clusters is possible.

API Server URL and CA certificate

In order for your Fleet management installation to properly work it is important the correct API server URL and CA certificates are configured properly. The Fleet agents will communicate to the Kubernetes API server URL. This means the Kubernetes API server must be accessible to the downstream clusters. You will also need to obtain the CA certificate of the API server. The easiest way to obtain this information is typically from your kubeconfig file ($HOME/.kube/config). The server, certificate-authority-data, or certificate-authority fields will have these values.

$HOME/.kube/config

  1. apiVersion: v1
  2. clusters:
  3. - cluster:
  4.     certificate-authority-data: LS0tLS1CRUdJTi...
  5.     server: https://example.com:6443

Extract CA certificate

Please note that the certificate-authority-data field is base64 encoded and will need to be decoded before you save it into a file. This can be done by saving the base64 encoded contents to a file and then running

  1. base64 -d encoded-file > ca.pem

Next, retrieve the CA certificate from your kubeconfig.

  • Extract First
  • Multiple Entries

If you have `jq` and `base64` available then this one-liners will pull all CA certificates from your `KUBECONFIG` and place then in a file named `ca.pem`.

  1. kubectl config view -o json --raw  | jq -r '.clusters[].cluster["certificate-authority-data"]' | base64 -d > ca.pem

Or, if you have a multi-cluster setup, you can use this command:

  1. # replace CLUSTERNAME with the name of the cluster according to your KUBECONFIG
  2. kubectl config view -o json --raw  | jq -r '.clusters[] | select(.name=="CLUSTERNAME").cluster["certificate-authority-data"]' | base64 -d > ca.pem

Extract API Server

If you have a multi-cluster setup, you can use this command:

  1. # replace CLUSTERNAME with the name of the cluster according to your KUBECONFIG
  2. API_SERVER_URL=$(kubectl config view -o json --raw  | jq -r '.clusters[] | select(.name=="CLUSTER").cluster["server"]')
  3. # Leave empty if your API server is signed by a well known CA
  4. API_SERVER_CA="ca.pem"

Validate

First validate the server URL is correct.

  1. curl -fLk "$API_SERVER_URL/version"

The output of this command should be JSON with the version of the Kubernetes server or a 401 Unauthorized error. If you do not get either of these results than please ensure you have the correct URL. The API server port is typically 6443 for Kubernetes.

Next validate that the CA certificate is proper by running the below command. If your API server is signed by a well known CA then omit the --cacert "$API_SERVER_CA" part of the command.

  1. curl -fL --cacert "$API_SERVER_CA" "$API_SERVER_URL/version"

If you get a valid JSON response or an 401 Unauthorized then it worked. The Unauthorized error is only because the curl command is not setting proper credentials, but this validates that the TLS connection work and the ca.pem is correct for this URL. If you get a SSL certificate problem then the ca.pem is not correct. The contents of the $API_SERVER_CA file should look similar to the below:

ca.pem

  1. -----BEGIN CERTIFICATE-----
  2. MIIBVjCB/qADAgECAgEAMAoGCCqGSM49BAMCMCMxITAfBgNVBAMMGGszcy1zZXJ2
  3. ZXItY2FAMTU5ODM5MDQ0NzAeFw0yMDA4MjUyMTIwNDdaFw0zMDA4MjMyMTIwNDda
  4. MCMxITAfBgNVBAMMGGszcy1zZXJ2ZXItY2FAMTU5ODM5MDQ0NzBZMBMGByqGSM49
  5. AgEGCCqGSM49AwEHA0IABDXlQNkXnwUPdbSgGz5Rk6U9ldGFjF6y1YyF36cNGk4E
  6. 0lMgNcVVD9gKuUSXEJk8tzHz3ra/+yTwSL5xQeLHBl+jIzAhMA4GA1UdDwEB/wQE
  7. AwICpDAPBgNVHRMBAf8EBTADAQH/MAoGCCqGSM49BAMCA0cAMEQCIFMtZ5gGDoDs
  8. ciRyve+T4xbRNVHES39tjjup/LuN4tAgAiAteeB3jgpTMpZyZcOOHl9gpZ8PgEcN
  9. KDs/pb3fnMTtpA==
  10. -----END CERTIFICATE-----

Install for Multi-Cluster

In the following example it will be assumed the API server URL from the KUBECONFIG which is https://example.com:6443 and the CA certificate is in the file ca.pem. If your API server URL is signed by a well-known CA you can omit the apiServerCA parameter below or just create an empty ca.pem file (ie touch ca.pem).

Setup the environment with your specific values, e.g.:

  1. API_SERVER_URL="https://example.com:6443"
  2. API_SERVER_CA="ca.pem"

Once you have validated the API server URL and API server CA parameters, install the following two Helm charts.

  • Install
  • Verify

First install the Fleet CustomResourcesDefintions.

  1. helm -n cattle-fleet-system install --create-namespace --wait \
  2.     fleet-crd https://github.com/rancher/fleet/releases/download/v0.6.0/fleet-crd-0.6.0.tgz

Second install the Fleet controllers.

  1. helm -n cattle-fleet-system install --create-namespace --wait \
  2.     --set apiServerURL="$API_SERVER_URL" \
  3.     --set-file apiServerCA="$API_SERVER_CA" \
  4.     fleet https://github.com/rancher/fleet/releases/download/v0.6.0/fleet-0.6.0.tgz

Fleet should be ready to use. You can check the status of the Fleet controller pods by running the below commands.

  1. kubectl -n cattle-fleet-system logs -l app=fleet-controller
  2. kubectl -n cattle-fleet-system get pods -l app=fleet-controller
  1. NAME                                READY   STATUS    RESTARTS   AGE
  2. fleet-controller-64f49d756b-n57wq   1/1     Running   0          3m21s

At this point the Fleet manager should be ready. You can now register clusters and git repos with the Fleet manager.