Create a cluster

Node Discovery and Autocluster

EMQ X supports Autocluster based on the Ekka library. Ekka is a cluster management library developed for Erlang/OTP applications, supporting Erlang Node Auto-Discovery, Autocluster, Network Partition Autoheal and Autoclean.

EMQ X supports multiple node discovery strategies:

Introduction to cluster management through manual method

Suppose you are going to deploy an EMQ X cluster on two servers of s1.emqx.io, s2.emqx.io:

Tip

The format of node name is Name@Host, and Host must be an IP address or FQDN (host name. domain name)

Configure emqx@s1.emqx.io node

emqx/etc/emqx.conf:

node.name = emqx@s1.emqx.io
# or
node.name = emqx@192.168.0.10

You can also configure through environment variables:

export EMQX_NODE_NAME=emqx@s1.emqx.io && ./bin/emqx start

Tip

After the node joins the cluster, the node name cannot be changed.

Configure emqx@s2.emqx.io Node

emqx/etc/emqx.conf:

node.name = emqx@s2.emqx.io
# or
node.name = emqx@192.168.0.20

Node joins the cluster

After starting the two nodes, execute the following on s2.emqx.io:

$ ./bin/emqx_ctl cluster join emqx@s1.emqx.io
Join the cluster successfully.
Cluster status: [{running_nodes,['emqx@s1.emqx.io','emqx@s2.emqx.io']}]

Tip

After s2.emqx.io joins the cluster, all its data will be cleared and the data of the s1.emqx.io node will be synchronized. If there are still s3.emqx.io nodes, you need to execute commands on the s3.emqx.io node to join emqx@s1.emqx.io or emqx@s2.emqx.io, and nodes already existing in the cluster cannot join other nodes. Otherwise, it will exit the current cluster and form a new cluster with the new joined node.

Query the cluster status on any node:

$ ./bin/emqx_ctl cluster status
Cluster status: [{running_nodes,['emqx@s1.emqx.io','emqx@s2.emqx.io']}]

Exit the cluster

There are two ways for a node to exit the cluster:

1. leave: Make this node leave the cluster
2. force-leave: delete other nodes from the cluster

Make emqx@s2.emqx.io actively exit the cluster:

$ ./bin/emqx_ctl cluster leave

Or delete the emqx@s2.emqx.io node from the cluster on s1.emqx.io:

$ ./bin/emqx_ctl cluster force-leave emqx@s2.emqx.io

Firewall settings

The Node Discovery Ports

If the environment variable WITH_EPMD=1 is set in advance, the epmd (listening port 4369) will be enabled for node discovery when emqx is started, which is called epmd mode.

If the environment variable WITH_EPMD is not set, epmd is not enabled when emqx is started, and emqx ekka is used for node discovery, which is also the default method of node discovery since version 4.0. This is called ekka mode.

epmd mode：

If there is a firewall between cluster nodes, the firewall needs to open TCP port 4369 for each node, to allow peers query each other’s listening port. The firewall should also allow nodes connecting to port in configurable range from node.dist_listen_min to node.dist_listen_max (inclusive, default is 6369 for both)

ekka mode（Default mode since version 4.0）：

In ekka mode, the port mapping is conventional, but not dynamic as in epmd mode. The configurations node.dist_listen_min and node.dist_listen_max take no effect in this case.

If there is a firewall between the cluster nodes, the conventional listening port should be allowed for nodes to connect each other. See below for port mapping rule in ekka mode.

Erlang distribution port mapping rule in ekka mode: ListeningPort = BasePort + Offset, where BasePort is 4370 (which is not made configurable), and Offset is the numeric suffix of the node’s name. If the node name does not have a numeric suffix, Offsset is 0.

For example, having node.name = emqx@192.168.0.12 in emqx.conf should make the node listen on port 4370, and port 4371 for emqx1 (or emqx-1), and so on.

The Cluster PRC Port

Each emqx node also listens on a (conventional) port for the RPC channels, which should also be allowed by the firewall. The port mapping rule is similar to the node discovery ports in ekka mode, but with the BasePort = 5370. That is, having node.name = emqx@192.168.0.12 in emqx.conf should make the node listen on port 5370, and port 5371 for emqx1 (or emqx-1), and so on.