This document describes how to simulate network faults using NetworkChaos in Chaos Mesh.

NetworkChaos introduction

NetworkChaos is a fault type in Chaos Mesh. By creating a NetworkChaos experiment, you can simulate a network fault scenario for a cluster. Currently, NetworkChaos supports the following fault types:

• Partition: network disconnection and partition.
• Net Emulation: poor network conditions, such as high delays, high packet loss rate, packet reordering, and so on.
• Bandwidth: limit the communication bandwidth between nodes.

Notes

Before creating NetworkChaos experiments, ensure the following:

1. During the network injection process, make sure that the connection between Controller Manager and Chaos Daemon works, otherwise the NetworkChaos cannot be restored anymore.
2. If you want to simulate Net Emulation fault, make sure the NET_SCH_NETEM module is installed in the Linux kernel. If you are using CentOS, you can install the module through the kernel-modules-extra package. Most other Linux distributions have installed the module already by default.

Create experiments using Chaos Dashboard

1. Open Chaos Dashboard, and click NEW EXPERIMENT on the page to create a new experiment:

   

2. In the Choose a Target area, choose NETWORK ATTACK and select a specific behavior, such as LOSS. Then fill out specific configuration.

   

   For details of specific configuration fields, refer to Field description.

3. Fill out the experiment information, and specify the experiment scope and the scheduled experiment duration.

   

4. Submit the experiment information.

Create experiments using the YAML files

Net emulation example

1. Write the experiment configuration to the network-delay.yaml file, as shown below:

   apiVersion: chaos-mesh.org/v1alpha1
   kind: NetworkChaos
   metadata:
     name: delay
   spec:
     action: delay
     mode: one
     selector:
       namespaces:
         - default
       labelSelectors:
         'app': 'web-show'
     delay:
       latency: '10ms'
       correlation: '100'
       jitter: '0ms'

This configuration causes a latency of 10 milliseconds in the network connections of the target Pods. In addition to latency injection, Chaos Mesh supports packet loss and packet reordering injection. For details, see field description.

1. After the configuration file is prepared, use kubectl to create an experiment:

   kubectl apply -f ./network-delay.yaml

Partition example

1. Write the experiment configuration to the network-partition.yaml file, as shown below:

   apiVersion: chaos-mesh.org/v1alpha1
   kind: NetworkChaos
   metadata:
     name: partition
   spec:
     action: partition
     mode: all
     selector:
       namespaces:
         - default
       labelSelectors:
         'app': 'app1'
     direction: to
     target:
       mode: all
       selector:
         namespaces:
           - default
         labelSelectors:
           'app': 'app2'

This configuration blocks the connection created from app1 to app2. The value for the direction field can be to, from or both. For details, refer to Field description.

1. After the configuration file is prepared, use kubectl to create the experiment:

   kubectl apply -f ./network-partition.yaml

Bandwidth example

1. Write the experiment configuration to the network-bandwidth.yaml file, as shown below:

   apiVersion: chaos-mesh.org/v1alpha1
   kind: NetworkChaos
   metadata:
     name: bandwidth
   spec:
     action: bandwidth
     mode: all
     selector:
       namespaces:
         - default
       labelSelectors:
         'app': 'app1'
     bandwidth:
       rate: '1mbps'

This configuration limits the bandwidth of app1 to 1 mbps.

1. After the configuration file is prepared, use kubectl to create the experiment:

   kubectl apply -f ./network-bandwidth.yaml

Field description

Field description

Description for action-related fields

For the Net Emulation and Bandwidth fault types, you can further configure the action related parameters according to the following description.

• Net Emulation type: delay, loss, duplicated, corrupt
• Bandwidth type: bandwidth

delay

Setting action to delay means simulating network delay fault. You can also configure the following parameters.

The computational model for correlation is as follows:

1. Generate a random number whose distribution is related to the previous value:

   rnd = value * (1-corr) + last_rnd * corr

rnd is the random number. corr is the correlation you fill out before.

1. Use this random number to determine the delay of the current packet:

   ((rnd % (2 * sigma)) + mu) - sigma

   In the above command, sigma is jitter and mu is latency.

reorder

Setting action to reorder means simulating network packet reordering fault. You can also configure the following parameters.

loss

Setting action to loss means simulating packet loss fault. You can also configure the following parameters.

duplicate

Set action to duplicate, meaning simulating package duplication. At this point, you can also set the following parameters.

corrupt

Setting action to corrupt means simulating package corruption fault. You can also configure the following parameters.

For occasional events such as reorder, loss, duplicate, and corrupt, the correlation is more complicated. For specific model description, refer to NetemCLG.

bandwidth

Setting action to bandwidth means simulating bandwidth limit fault. You also need to configure the following parameters.

For more details of these fields, you can refer to tc-tbf document.